Murata WIT2410NF Скачать руководство пользователя страница 20

Страница: 20 / 58

WIT2410

2000- 2005 Murata



Inc

M-2410-0000 Rev G

Protocol Modes Definitions

mode 00

Transparent mode used for point-to-point networks
or multipoint remotes; does not support any packet
types.

mode 01

This is the simplest protocol mode supporting Data
packets only. This mode is not recommended for
base radios. No

CONNECT

DISCONNECT

packets are supported and no sequence numbers are
provided.

packet types supported: Data

mode 02

This mode includes notification when remotes are
registered or dropped through

CONNECT

and

DISCONNECT

packets that are sent to the user

application at the base station and at the remote. No
sequence numbers are provided.

packet types supported: Data

CONNECT

DISCONNECT

mode 04

This is the packet format used by the WIT2400.
This allows legacy software to operate the
WIT2410 with a minimum of changes. Note
however, that since different air data rates are used,
WIT2410s and WIT2400s cannot be mixed in a
network.

packet types supported: 2400 data format

(addresses must be limited to 1..62)

modes 05 – 08

reserved for future use.

mode 09

This mode sends the protocol mode 01 packets
during transmit but receives data transparently.

mode 0A

This mode sends the protocol mode 02 packets
during transmit but receives data transparently

mode 0C

This mode sends the protocol mode 04 packet
during transmit but receives data transparently

modes 0D – 0F

reserved for future use.

mode 11

This mode sends data transparently but supports
protocol mode 1 during reception

Содержание WIT2410NF



























































Результаты поиска

Содержание WIT2410NF

Отзывы:

Похожие инструкции для WIT2410NF

Бренды по названию

Популярные бренды

Murata WIT2410NF, Руководство по интеграции

Результаты поиска

Содержание WIT2410NF

Отзывы:

Похожие инструкции для WIT2410NF

Бренды по названию

Популярные бренды