Munters MIR 37 WU Скачать руководство пользователя страница 5

________________________________________________________________________________________________ 

4. INSTALLATION INSTRUCTIONS

 

 

4.1. General instructions 

 

 

THE  INSTALLATION  OF  THE  EQUIPMENT  SHALL  BE  IN  ACCORDANCE  WITH  THE 

REGULATION OF AUTHORITIES HAVING JURISDICTION AND CSA B139.  

 

The heater must be operated  only  by  properly trained personnel. The manufacturer’s instructions must be 

followed. 

 

The heater must be installed and operated so that people are not exposed to dangers deriving from exhaust 

gases, from the hot air flow and in such a way that no fire risks exist. 

 

It is forbidden to install the heater in the surroundings of flammable materials, combustible products, or in 

explosive atmospheres.  

 

When  an 

indirect-fired

  heater  connected  to  a  flue  pipe  is  used  in  a  closed  room,  provide  a  minimum 

opening area of 1 ft³ per US gallon capacity at the unit level. 

 

When a 

direct-fired

 heater - or an 

indirect-fired

 heater 

not 

connected to a flue pipe -  is used in a closed 

room, provide a minimum opening area of  3 ft

2

 per US gallon capacity at the unit level and a continuous, natural 

air circulation through windows and doors.  

 

For the use of the heater the general and special fire safety regulations in force in all fields of applications 

must be followed. In any case the following minimum safety clearances from flammable materials or objects in 
the surroundings of the heater must be ensured:   
 

Sides:        

2 ft   (610 mm) 

Air inlet :    

2 ft  (610 mm) 

Top: 

     

5 ft   (1520 mm)  

Air outlet:    

10 ft (3050 mm) 

Flue pipe:   

3 ft   (915 mm) 

 

 

 

Floors and ceilings must be made of fireproof materials in the place where the heater is operated. 

 

The air inlet and outlet must never be blocked for any reason. 

 

Install the heater on a flat, level floor in a steady position. 

 

It is forbidden to connect direct-fired heaters to air ducts. 

 

4.2 Assembling the heater 
 

 

Before operating the heater, assemble axle, wheels and lower support following the diagram below: 

 
  
 

 

 
 
 

Содержание MIR 37 WU











Отзывы: