Munsch MAK-36 Скачать руководство пользователя страница 9

 
 

 

 

 

MEK-36,48,58 / MAK-36,48,58 

Issue 12.2009/Rev. 02 

Page 9/20 

 

Melt and preheat temperatures are controlled 
separately. The setpoint and momentary values are 
displayed concurrently. 
 

 

The melt temperature must have reached the preset 
start interlock temperature for the startup timer to 
be activated. After the startup timer has timed out, 
the start interlock will be released and the extruder 
can be started. 

 
 

The temperature-controlled start interlock prevents 
the drive from starting if there is still unmolten 
material in the extruder, thus precluding damage to 
the unit.  

 

The output rate is variable so that the preheat 
temperature can be matched to the weld thickness. 
 

5  Startup and Shutoff 

5.1  General  
In addition to the operating instructions and the 
national and local accident prevention regulations 
applicable at the place of use, the acknowledged 
technical rules for safe and proper working practices 
must be observed. 

 

Any working practices posing a safety risk are 
prohibited. 

 

Before starting / shutting off the hand extruder, make 
sure to carefully read the instructions under section 
“Safety”. 

 

Only trained and qualified personnel may be 
assigned to the operation of the hand extruder. 
 
5.2  Preparation 

  Place hand extruder on a firm support and secure 

it against toppling over as shown in the 
illustration.  

 

 

 

 

  Mount hot air hood   

 

  Position handle  

Loosen handle (55) and move it to the ideal 
working position by pushing it back and forth. The 
extruder handles can be additionally swivelled 
upward and downward, so that the machine can 
be operated by both right-handed and left-handed 
persons. 

 

  Position T-grip on “landfill” extruder version   

To rotate the T-grip, loosen it and then retighten it 
in the desired position.  

 

  Only for type MEK hand extruder with external 

air supply: 
Connect the hand extruder to the external air 
source using the hose coupling LW 13 / NM 7.2 
provided for this purpose (quick connect-
disconnect); set air rate to 300 l/min at 0.4 bar. A 
suitable controller with flow metering function is 
recommended for setting the air rate.

 

 

 

CAUTION The supply air must be clean, dry and 

free from oil and water.  

 

Never connect an external air source to a  
MAK hand extruder. 

Содержание MAK-36





















Отзывы: