Munsch MAK-36 Скачать руководство пользователя страница 10

 
 

Hand Extruder MEK-36,48,58 / MAK-36,48,58 

 

Page10/20 

Issue 12.2009/Rev. 02 

MUNSCH Kunststoff-Schweißtechnik GmbH 

 

 

  Mount welding shoe 

-   Select the welding shoe required for the  
    specific weld geometry or machine a welding 
    shoe blank to the required geometry.  
-   Observe DVS 2207 Guideline, Part 4 for  
    machining welding shoe blanks.  
-   Mount welding shoe to the hand extruder in 
    the position required for welding.  
    Observe welding direction! 
    Tighten set screw (25). 
 

  Mount preheat nozzle  

-   Select and mount the preheat nozzle (4)  
    required for the specific weld geometry.  
-   Observe spacing A = 5 mm. 
-   Tighten the preheat nozzle using set screw  
    (25.1) or mushroom head screw (125.22).  

 
 

    

   

 

 
 
Table: Preheat nozzle 

         

 

Care must be taken to ensure that the preheat  
nozzle provides intensive and uniform preheating 
(melting) of the base material over the entire joint 
width at as low a hot air temperature as possible. For 
larger weld seam widths, a wider preheat nozzle is 
available as an accessory. 

 

 
5.3  Starting the hand extruder 

 Observe section “Safety“.  

 

  CAUTION Never operate the hand extruder 

without air supply. Otherwise the unit may suffer 
severe damage. 
 

  CAUTION Before plugging in the mains 

connector, check that the drive unit is not set to 
continuous operation. 
 

  CAUTION The hot air hood must be in place. 

 

    

  CAUTION Start external air supply for MEK hand 

extruder.  
 

  CAUTION Plug in mains connector.  

 

  CAUTION In the case of the MAK hand extruder 

with integrated air supply, the blower must start 
automatically. 

 

  CAUTION Once air exits the preheat nozzle (4), 

the heating systems for the air/melt temperatures 
may be activated. 

 

 

  For the operation of the temperature controller, 

see section 5.5 “Set temperatures“. For 
temperature settings, see page 12.  

  The hand extruder will reach its operating 

temperature after about  10 to 15 minutes.  

 

 
 

Содержание MAK-36





















Отзывы: