background image

REFRIGERANT PIPE CONNECTION

8

4. Refrigerant pipe connection

Oblique

90

Roughness

Burr

Main cause for refrigerant leakage
is due to defect in the flaring work. 
Carry out correct flaring work
using the following procedure:

A: Cut the pipes and the cable.

1. Use the piping kit accessory or pipes 
    purchased locally.
2. Measure the distance between the indoor 
    and the outdoor unit.
3. Cut the pipes a little longer than the 
    measured distance.
4. Cut the cable 1.5m longer than the pipe  
    length.

1. Flaring work

Pipe

Reamer

Point down

Fig.54

Fig.55

B: Burr removal

1. Completely remove all burrs from the cut 
     cross section of pipe/tube.
2. Put the end of the copper tube/pipe in a 
    downward direction as you remove burrs in 
    order to avoid dropping burrs into the tubing.

Flare nut

Copper tube

Fig.56

C: Putting nut on

     Remove flare nuts attached to indoor and 
     outdoor unit, then put them on pipe/tube 
      having completed burr removal.(not possible
      to put them on after flaring work) 

Additional charge (R410A)

Max. Length for all rooms (m)

OU higher than IU

OU lower than IU

10 

10 

10 

10 

15 

15 

15 

15 

UNIT

Max. Leng th for one indoor unit (m)

Max. height different between
indoor and outdoor unit (m)

Max. height different between indoor units (m)

Before installing, make sure that the height difference, the length of refrigerant pipe and number of bends
between indoor and outdoor units, meet the following specifications.

2 x 1 (H6.2)

3 x 1 (H6.3)

4 x 1 (H6.4)

5 x 1 (H6.5)

30 

45 

60 

75 

25 

30 

35 

35 

15 

15 

15 

15 

10m

15m

15m

Outdoor unit

Indoor unit

Max. height difference

Indoor unit

Indoor unit

 

 

 

 

2 x 1 (H6.2)

3 x 1 (H6.3)

4 x 1 (H6.4)

5 x 1 (H6.5)

 

Charged until

(g) 

UNIT

Total Liquid Length 1/4":

15 x (Total length - 15)

30 x (total length - 7,5)

15m

30m (Total Liquid Length 1/4")

(Total Liquid Length 1/4")

22,5m

7,5m (Total Liquid Length 3/8")

37,5m (Total  Liquid Length 1/4")

Additional

charge

(Total Liquid Length 1/4")

Total Liquid Length 1/4":

Total Liquid Length 1/4":

Total Liquid Length 1/4":

15 x (Total length - 22,5)

15 x (Total length - 30)

15 x (Total length - 37,5)

Total Liquid Length 3/8":

7,5m (Total Liquid Length 3/8")

Содержание H6M Series



















































Отзывы: