NOTE
Remark per EMC Directive 89/336/EEC
For to prevent flicker impressions during the start of the
compressor (technical process), following installation condi-
tions apply.
The power connection for the air conditioner has to be done
at the main power distribution.The distribution has to be of
a low impedance, normally the required impedance reaches
at a 32A fusing point.
No other equipment has to be connected with this power
line.
For detailed installation acceptance, please refer to your
contract with the power supplier if restrictions do apply for
p r o d u c t s l i k e w a s h i n g m a c h i n e s , a i r c o n d i t i o n e r s o r
electrical ovens.
●
●
●
There is combustible gas or materials.
There is much evaporating acid or alkaline gas.
Other special areas.
Notes Before Installation
Select the correct carry-in path.
Move this unit as originally packaged as possible.
If the air conditioner is installed on a metal part of the building, it
must be electrically insulated according to the relevant standards
to electrical appliances.
Avoid installing it in a narrow sapce which has a high requirement
to noise.
●
●
●
●
●
●
●
Please refer to the following figure for the distance measurement
between the screw bolts.
Please install with screw bolts.
The handling to the ceiling varies from the constructions, consult
the construction personnels for the specific procedures.
The size of the ceiling to be handled.Do keep the ceiling flat.
Consolidate the roof beam for possible vibration.
Cut off the roof beam.
Strengthen the place cut off, and consolidate the roof beam.
Carry out the pipe and line operation in the ceiling after finishing
the installation of the main body. While choosing where to start
the operation, determine the direction of the pipes to be drawn
out. Especially in case there is a ceiling, position the refrigerant
pipes, drain pipes, indoor & outdoor lines to the connection
places before hanging up the machine.
The installation of hanging screw bolts.
●
●
●
Installing Φ10 Hanging Screw Bolts (4 Bolts)
4. INDOOR UNIT INSTALLATION
Cautions on remote controller installation
Never throw or beat the controller.
Before installation, operate the remote controller to determine
its location in a reception range.
Keep the remote controller at least 1m apart from the nearest
TV set or stereo equipment. (It is necessary to prevent image
disturbances or noise interferences.)
Do not install the remote controller in a place exposed to direct
sunlight or close to a heatingsource, such as a stove. Note that
the positive and negative poles are in right positions when
loading batteries.
●
●
●
●
1. Remote controller....................................1
2. Remote controller holder.........................1
3. Mounting screw
(ST2.9x10-C-H)........................................2
4. Alkaline dry battery(AM4)
..................................................................2
Remote controller & Its Frame
2
3
Remot e controller
holder
Mounting screw
Fig.3-1
For power details of the air conditioner, refer to the rating
plate of the product.
For any question contact your local dealer.
●
●
1
Remot e
controller
Table.3-1
The following are selectable accessories
3. ACCESSORIES
1
1
1
Name of
Accessories
Installation manual
Pipe insula-
tion material
Adhesive tape
for seal
Heat insulation
To connect drain pipe
Q‘ty
4
(This manual)
Outline
Usage
Wire
control the
air-conditioner
Clasp
Network
matching wire
1
1
1
Water outlet joint
For drainage
Chucking the joint which
connect the drain hose
and the outlet of indoor
unit
The indoor unit which at the
terminal of communication
system shouldconnect a
impedance between port
P and port Q
20-28kw
2
Water connec-
ting pipe
20-28kw
1
To connect drain pipe
Wire controller
12.5-14kw
12.5-14kw
12.5-14kw
20-28kw
2
Copper nut
1
Use for pipe connection
of engineering installation
maintenance of motor
˖
2
12.5-14kw
20-28kw
Electric throttle
connect part A
Electric throttle
connect part B
20-28kw
20-28kw
1
1
Connect electric throttle
part A
Connect electric throttle
part B
Spring
20-28kw
1
To fixed display box
0 1 2
F
3
E
4
D
5
C
6
B
7
A
89
0 1 2
F
3
E
4
D
5
C
6
B
7
A
89
Installation manual
2
Duct 100% fresh air
