background image

CommPlete Communications Server

v

Canadian Limitations Notice

Notice:

 The ringer equivalence number (REN) assigned to each terminal device provides an indication of

the maximum number of terminals allowed to be connected to a telephone interface.  The termination of a
interface may consist of any combination of devices subject only to the requirement that the sum of the
ringer equivalence numbers of all the devices does not exceed 5.

Notice:

 The Industry Canada label identifies certificated equipment. This certification means that the

equipment meets certain telecommunications network protective, operational and safety requirements.
The Industry Canada does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities
of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. The customer should be aware that compliance with the above conditions may not
prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated
by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to disconnect the
equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This precaution
may be particularly important in rural areas.

Caution: 

Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulation of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édicté
par le ministère des Communications du Canada.

Ringer Equivalence Number

Notice

: The ringer equivalence number (REN) asigned to each terminal device provides an indication of

the maximum number of terminals allowed to be connected to a telephone interface. The termination on
an interface may consist of any combination of devices subject only to the requirement that the sum of the
ringer equivalence numbers of all the devices does not exceed 5.

Cooling Requirements

The ambient operating temperature of the CC9600 chassis is 0° C to 40° C.

Important Safety Requirements

 

No manual adjustments to the equipment are necessary for connection to mains power within rated
voltage and frequency.

Содержание CommPlete CC9600



























Отзывы: