background image

HTXD6i/STXD6i Trowel • SeTUp, aDJUSTMeNTS aND CalIBraTIoNS — rev. #0 (03/14/13) — page 5

geNeral SaFeTY

  CaUTIoN

 

„

Never

 operate this equipment without proper protective 

clothing,  shatterproof  glasses,  respiratory  protection, 

hearing protection, steel-toed boots and other protective 

devices required by the job or city and state regulations.

 

„

Avoid wearing jewelry or loose fi tting clothes that may 

snag on the controls or moving parts as this can cause 

serious injury.

 

„

Never

 operate this equipment when not 

feeling well due to fatigue, illness or when 

under medication.

 

„

Never

 operate this equipment under the 

infl uence of drugs or alcohol. 

 

„

alwaYS

 clear the work area of any debris, tools, etc. 

that would constitute a hazard while the equipment is 

in operation.

 

„

No one other than the operator is to be in the working 

area when the equipment is in operation.

 

„

Do NoT

 use the equipment for any purpose other than 

its intended purposes or applications.

  NOTICE

 

„

This equipment should only be operated by trained and 

qualifi ed personnel 18 years of age and older.

 

„

Whenever necessary, replace nameplate, operation and 

safety decals when they become diffi cult read.

 

„

Manufacturer  does  not  assume  responsibility  for  any 

accident due to equipment modifi cations. Unauthorized 

equipment modifi cation will void all warranties.

 

„

Never

 use accessories or attachments that are not 

recommended by Multiquip for this equipment. Damage 

to the equipment and/or injury to user may result.

 

„

alwaYS

 know the location of the nearest 

fi re extinguisher.

 

„

alwaYS 

know the location of the nearest 

fi rst aid kit.

 

„

alwaYS

 know the location of the nearest phone or 

keep 

a phone on the job site.

 Also, know the phone numbers 

of the nearest 

ambulance, doctor 

and 

fi re department. 

This  information  will  be  invaluable  in  the  case  of  an 

emergency.

safety information

Содержание Whiteman HTXD6i

































Отзывы:

Похожие инструкции для Whiteman HTXD6i