SMART SX
_________________________________________________________________________________________________________
Page 25
SMART S
X in
stru
ctions # 9
85 53
35 (
2
3.07
.2012
Pa
Ch)
•
Error
s
and
omissio
n
s e
x
cep
ted
•
©
M
U
LT
IPL
E
X
to program model memory 1 in the transmitter and set
it up himself.
The receiver with the code ‘ID 2’ (# 5 5823) activates
model memory 2 in the transmitter, to which the mod-
el ‘Easy Star II’ is assigned.
The receiver with the code ‘ID 3’ (# 5 5824) activates
model memory 3 in the transmitter, to which the
model ‘Easy Glider’ is assigned.
The receiver with the code ‘ID 5’ (# 5 5826) activates
model memory 5 in the transmitter, to which the mod-
el ‘Razzor’ is assigned.
The receiver with the code ‘ID 6’ (# 5 5827) activates
model memory 6 in the transmitter, to which the
model ‘FunCopter’ is assigned.
The receivers with the codes ‘ID 21’ (# 5 5828) and ‘ID 22’
(# 5 5829) activate model memories 21 and 22 in the trans-
mitter respectively, to which no models are assigned; they
are freely available, like the receiver with ‘ID 1’.
7.16 Installing the receiver in the model
If you intend to fly a MULTIPLEX RTF or RR+ model, the
receiver is installed in the correct manner as standard. If
you wish to fly a different model, you must install an M-
LINK receiver as described in the corresponding MULTI-
PLEX operating instructions. Please pay particular attention
to the aerial deployment:
•
Do not shorten or extend the aerial or its feed cable! If
you need a longer or shorter aerial lead, please contact
the MULTIPLEX Service Department, or a MULTIPLEX
Service Centre.
•
Install the receiver in the model in such a way that the
aerial is as far away as possible from any conductive
material.
•
If your model’s fuselage is made of electrically conduc-
tive material (e.g. carbon fibre), then the aerial must be
installed in such a way that the active part (the final 30
mm) is located outside the model.
•
Do not deploy the aerial parallel to servo leads, high-
current cables or electrically conductive parts (e.g.
pushrods).
All other information can be found in the instructions sup-
plied with your receiver.
7.17 The SMART SX as Pupil transmitter
The SMART SX transmitter is prepared as standard for use
in a wireless Trainer system; the Teacher transmitter can
be any MULTIPLEX M-LINK transmitter fitted with a multi-
function socket. The MULTIPLEX Trainer Stick can be
plugged into this socket on the Teacher transmitter. A
SMART SX transmitter will detect the presence of the stick,
and switch automatically to Pupil mode. If you are using a
PROFI TX transmitter with integral COPILOT, the same
RX-5 M-LINK ID 1
(# 5 5822)
No model assignment
RX-5 M-LINK ID 2
(# 5 5823)
Model: Easy Star II
RX-5 M-LINK ID 3
(# 5 5824)
Model: Easy Glider
RX-5 M-LINK ID 5
(# 5 5826)
Model:
Razzor
RX-5 M-LINK ID 6
(# 5 5827)
Model:
FunCopter
RX-5 M-LINK ID 21
(# 5 5828)
RX-5 M-LINK ID 22
(# 5 5829)
Содержание SMART SX
Страница 2: ......