background image

Part Number: 9290312   May/17/2016

General Information 

Section 1

ELECTRICAL

 DANGER

Check all wiring connections, including factory 

terminals, before operation. Connections can become 

loose during shipment and installation.

 DANGER

Units with two power cords must be plugged into 

individual branch circuits. During movement, cleaning 

or repair it is necessary to unplug both power cords.

n

Warning

The machine must be wired and grounded in 

accordance with national and local electrical codes.

Minimum Circuit Ampacity

The minimum circuit ampacity is used to help select the wire 

size of the electrical supply. (Minimum circuit ampacity is not 

the N2Fusion System’s running amp load.) The wire size (or 

gauge) is also dependent upon location, materials used, length 

of run, etc., it must be determined by a qualified electrician.

Voltage

A dedicated electrical circuit is required, a power cord is 

provided with all units. Some models are available in different 

voltages and may be equipped with a different plug.
The following precautions must be observed:
•  The equipment must be grounded.
•  A separate fuse/circuit breaker must be provided for 

each unit.

•  A qualified electrician must determine proper wire size 

dependent upon location, materials used and length 

of run (minimum circuit ampacity can be used to help 

select the wire size).

•  The maximum allowable voltage variation is ±10% of 

the rated voltage at equipment start-up (when the 

electrical load is highest).

•  Check all green ground screws, cables and wire 

connections to verify they are tight before start-up.

Minimum Circuit Amperage Chart

Important

Due to continuous improvements, this information is 

for reference only. Please refer to the serial number tag 

to verify electrical data. Serial tag information overrides 

information listed on this page.

Model

Voltage/Cycle/Phase Total 

Amps HP

Breaker 

Size (Max)

ND21TS00

115/60/1

6.0 A 1/5

15 A

Grounding Instructions

This appliance must be grounded. In the event of 

malfunction or breakdown, grounding provides a path 

of least resistance for electric current to reduce the 

risk of electric shock. This appliance is equipped with a 

cord having an equipment-grounding conductor and 

a grounding plug. The plug must be plugged into an 

appropriate outlet that is properly installed and grounded 

in accordance with all local codes and ordinances.

n

Warning

When using electric appliances, basic precautions must 

always be followed, including the following:

A.  Read all the instructions before using the 

appliance.

B.  To reduce the risk of injury, close supervision 

is necessary when an appliance is used near 

children.

C.  Do not contact moving parts.

D.  Only use attachments recommended or sold by 

the manufacturer.

E.  Do not use outdoors.

F.  For a cord-connected appliance, the following 

must be included:

•  Do not unplug by pulling on cord. To unplug, 

grasp the plug, not the cord.

•  Unplug from outlet when not in use and 

before servicing or cleaning.

•  Do not operate any appliance with a 

damaged cord or plug, or after the appliance 

malfunctions or is dropped or damaged in 

any manner. Contact the nearest authorized 

service facility for examination, repair, or 

electrical or mechanical adjustment.

G.  Follow applicable lock out tag out procedures 

before working on equipment.

H.  Connect to a properly grounded outlet only. See 

Grounding Instructions.

Содержание N2-Fusion ND21TS01





























Отзывы: