background image

Package Should Contain:

1.  Proportioner unit .
2.  Discharge tube(s).
3.  Hose hook --3.5 GPM eductor only.
4. Mounting hardware.
5. Water inlet hose.
6. Instruction sheet.

THANK YOU FOR YOUR INTEREST IN OUR PRODUCTS

protective  clothing  and  eyewear  when  dispensing  chemicals  or  other  materials.

observe  safety  and  handling  instructions  of  the  chemical  manufacturers.

direct  discharge  away  from  you  or  other  persons  or  into  approved  containers.

dispense  cleaners  and  chemicals  in  accordance  with  manufacturer's  instructions.
Exercise 

CAUTION

  when  maintaining  your  equipment.

equipment  clean to maintain proper operation.

protective clothing and eyewear when working in the vicinity of all chemicals, filling or
emptying equipment or changing metering tips.

re-assemble  equipment  according  to  instruction  procedures.  Be  sure  all  components
are firmly screwed or latched into position.

only to tap water outlets (85 PSI maximum).

If the unit is used to fill a sink or the discharge hose can be placed into a sink, the unit
must be mounted so that the bottom of the cabinet is above the overflow rim of the sink.

WEAR

ALWAYS

ALWAYS

ALWAYS

KEEP

WEAR

ALWAYS

ATTACH

 Please use this equipment carefully and observe all warnings and cautions.
*******************************************************NOTE  ********************************************

NOTE

Continued..Next Page

Ins

tallation & Operation:

1. Remove cover by press-

ing tabs under cover.

2a.Remove  unit  mounting bracket from back of dispenser

by depressing the tabs.

2b. Slide bracket down.

3. Drill holes for  four wall

anchors with a 5/16"
drill bit. Use the mount-
ing bracket  as a tem-
plate for proper spacing
of the mounting screws.
Install anchors, and then
screw into anchors.

5. Secure  dispenser to

bracket by sliding lock-
ing bar through back of
unit. Replace cover.

4. Place  dispenser  on

bracket.

6. Attach short  discharge

tube on 1 GPM (grey)
eductor, then attach
longer  discharge  tube
on 3.5 GPM (yellow)
eductor.

7. Place hose hook on end

of  3.5 GPM discharge
tube. Hang on dispenser
when not in use.

2a.

2b.

s

s

s

s

DILUTION CONTROL SYSTEM

DSP-7077

Содержание e.Mix DSP-7077

Страница 1: ... outlets 85 PSI maximum If the unit is used to fill a sink or the discharge hose can be placed into a sink the unit must be mounted so that the bottom of the cabinet is above the overflow rim of the sink WEAR ALWAYS ALWAYS ALWAYS KEEP WEAR ALWAYS ATTACH Please use this equipment carefully and observe all warnings and cautions NOTE NOTE Continued Next Page Installation Operation 1 Remove cover by p...

Страница 2: ...3 10082830 Swivel collar molded 4 10075925 Pipe plug 5 10075980 Valve parts kit a diaphragm b armature c spring d valve bonnet 6 10079010 Spring 7 10079000 Magnet 8a 10084231 1 0 GPM flow control kit b 10084232 3 5 GPM flow control kit 9a 10089941 Eductor lock left b 10089937 Eductor lock right 10 10089938 Vent seal 11 10089983 Magnet pusher kit includes 9 10 12a 290SMP 1 0 GPM eductor assembly b ...

Страница 3: ...Parts Diagram 6 5 a b c d 2 3 1 9a 9b 15b 18a 18b 15a 17 20 7 10 10 11 11 12b 12a 13 13 14b 14a 4 16 21 22 BottleFill Chemical Inlet Bucket Fill Chemical inlet Top view of chemical inlet port 19 8a b ...

Страница 4: ... onto eductor discharge ring not in place hose barb or replace tube if it doesn t have a flooding ring d Clogged water inlet strainer d Disconnect inlet water line and clean strainer 3 Foaming in discharge a Concentrate container a Replace with new concentrate container malfunctioning b Air leak in pick up assembly b Replace pick up assembly with kit c Poor vent seal c Replace vent seal 9 on parts...

Отзывы: