MTU 20 V 4000 M73 x Скачать руководство пользователя страница 69

Страница: 69 / 205

4.16 Emergency stop from LOP

NOTICE

An emergency stop causes extreme stress to the engine plant.

Risk of overheating, damage to components!

• Initiate emergency stop only in emergency situations.

Emergency stop from LOP

Item

Measure

LOP

Open cap of illuminated EMERGENCY STOP pushbutton (→ Page 52).

LOP

Press EMERGENCY STOP illuminated pushbutton.

•

Engine is stopped by disconnecting the power supply to the ECU.

•

On engines with emergency-air shutoff flaps: flaps close;

•

EMERGENCY STOP illuminated pushbutton flashes. Horn, flashing

lamp etc. are tripped.

After emergency stop from LOP

Item

Measure

LOP

Press ALARM ACKNOWLEDGE illuminated pushbutton (→ Page 52).

•

Audible and visual signalization stops.

LOP

Press ALARM ACKNOWLEDGE button again.

•

Power supply to ECU is provided;

•

Alarm has been acknowledged.

Engine

On engines with emergency-air shutoff flaps: open flaps.

•

Engine is ready for starting.

MS150046/02E 2013-07 | Operation | 69

TIM-ID: 0000002314 - 004

Содержание 20 V 4000 M73 x














































































































































































































Результаты поиска

Содержание 20 V 4000 M73 x

Отзывы:

Похожие инструкции для 20 V 4000 M73 x

Бренды по названию

Популярные бренды

MTU 20 V 4000 M73 x, Руководство по эксплуатации

Результаты поиска

Содержание 20 V 4000 M73 x

Отзывы:

Похожие инструкции для 20 V 4000 M73 x

Бренды по названию

Популярные бренды