MTU 20 V 4000 M73 x Скачать руководство пользователя страница 68

Страница: 68 / 205

4.15 Stopping the engine from LOP

Preconditions

☑

Engine is running in local mode.

NOTICE

Stopping the engine when it is running at full load causes extreme stress to the engine.

Risk of overheating, damage to components!

• Before shutting down, disengage gear and run the engine at idle speed for at least 10 minutes

until engine temperatures have dropped and constant values are displayed.

Stopping the engine from LOP

Item

Measure

LOP

Disengage gearbox (→ Page 52).

LOP

Operate engine at idle speed (→ Page 52).

Temperature indications

Wait until engine temperatures do not fall any further.

LOP

Press STOP illuminated pushbutton (→ Page 52).

•

STOP button is illuminated.

•

Engine at a standstill.

68 | Operation | MS150046/02E 2013-07

TIM-ID: 0000002300 - 005

Содержание 20 V 4000 M73 x














































































































































































































Результаты поиска

Содержание 20 V 4000 M73 x

Отзывы:

Похожие инструкции для 20 V 4000 M73 x

Бренды по названию

Популярные бренды

MTU 20 V 4000 M73 x, Руководство по эксплуатации

Результаты поиска

Содержание 20 V 4000 M73 x

Отзывы:

Похожие инструкции для 20 V 4000 M73 x

Бренды по названию

Популярные бренды