manualshive.com logo in svg

MTS Sensors Level Plus LP Series, Инструкция по интерфейсу

Поделиться
Скачать
MTS Sensors Level Plus LP Series Скачать руководство пользователя страница 8

8

Modbus Interface Manual 

LP Series

Fault

Code

Description Corrective Action

101

Missing 

Magnet

• Verify Float Configuration is correct for the 

number of floats installed.

• Verify Float(s) are not in inactive zone.

• Verify Auto Threshold is enabled.

• Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

102

Internal 

Fault 1

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

103

Internal 

Fault 2

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

104

Internal 

Fault 3

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

105

Lobe Fault 1 • Verify Auto Threshold is enabled

• Cycle power to sensor.

• If proper operation is not restored, Contact 

Factory.

106

Lobe Fault 2 •  Verify Auto Threshold is enabled.

•  Cycle power to sensor.

•  If proper operation is not restored,  

    Contact Factory.

107

Delta Fault

Contact Factory to discuss application.

108

Internal 

Fault 4

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

109

Peak Fault

•  Verify Auto Threshold is enabled.

•  Cycle power to sensor.

•  If proper operation is not restored,  

    Contact Factory.

110

Hardware 

Fault 1

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

111

Power Fault

•  Cycle power to sensor.

•  Verify Power Supply rating.

•  Verify wiring.

•  If proper operation is not restored,  

    Contact Factory.

112

Hardware 

Fault 2

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

113

Hardware 

Fault 3

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

114

Hardware 

Fault 4

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

115

Timing 

Fault 1

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

116

Timing 

Fault 2

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

117

Timing 

Fault 3

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

118

DAC Fault 1

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

119

DAC Fault 2

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

8. Error Codes (Faults)

9. Modbus Interface

Note:

Termination and biasing of RS-485 data lines are as follows: 

Biasing

  

   Each LP-Series transmitter uses a Fail-Safe, Slew-Rate-Limited RS- 
     485/RS-422 Transceivers.  No additional biasing, resistors should  
     be present on the connecting devices (PLC, DCS, PC, Converter).

Termination

  

   Each LP-Series transmitter uses a Fail-Safe, Slew-Rate-Limited RS- 
     485/RS-422 Transceivers. No additional termination resistors are  
     necessary in connecting devices (PLC, DCS, PC, Converter).

Fault

Code

Description Corrective Action

120

DAC Fault 3

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

121

DAC Fault 4

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

122

SPI Fault 1

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

123

SPI Fault 2

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

124

Setpoint 

Fault

The analog setpoints are too close.  Mini-

mum distance is 150 mm (6 in.) for analog 

and 290 mm (11.5 in.) for SIL.  Adjust 

programmed setpoints as needed. (Analog 

only) If proper operation is not restored, 

Contact Factory.

125

Loop 1 Out 

of Range

Verify that magnets are positioned within 

expected measuring range.  Adjust program-

med setpoints as needed. (Analog only) If 

proper operation is not restored, Contact 

Factory.

126

Loop 2 Out 

of Range

Verify that magnets are positioned within 

expected measuring range.  Adjust program-

med setpoints as needed. (Analog only) If 

proper operation is not restored, Contact 

Factory.

127

EEPROM 

Fault 1

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

128

EEPROM 

Fault 2

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

129

Flash Failure Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

130

Internal 

Error

Cycle power to sensor.  If proper operation 

is not restored, Contact Factory.

Содержание Level Plus LP Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды