manualshive.com logo in svg

MTI SGR1500, Руководство оператора

Поделиться
Скачать
MTI SGR1500 Скачать руководство пользователя страница 11

19

20

SGR650, SGR1500 Specifications

Among the most critical elements of the stump grinder is the cutting wheel. It is also the most 
subject to damage and wear. In the course of grinding stumps it not only makes contact with the 
wood, but also encounters numerous abrasives and objects in the stump's environment, such as dirt, 
stones, large rocks and buried scrap.
The loss and wear of cutting teeth can significantly impair the efficiency and performance of the 
stump grinder. Therefore, it is important to make frequent inspections of the condition of all the 
cutting teeth and to replace any damaged or worn teeth

If a part needs replacement, only use parts that meet the manufacturer's specifications. Replace-
ment parts that do not meet specifications may result in a safety hazard or poor operation of the 
grinder.

Before attempting any maintenance, be sure that the engine is shut off, the spark plug wire is 
removed, and the engine is cool to the touch!

Thread in the bolt through the cutter wheel and into the teeth as 
shown, then tighten. Bolt should be torque to 60ft/lbs.

Installing Teeth

Item

(What to check or action req'd)

Engine Option

General

Cutter Wheel

Cutting Capacity

Teeth, Carbide Tips

SGR650

SGR1500

Daily

Each 

Use

10 

hours

20 

hours

40 

hours

Bearing, Shaft-Grease
Belt Tension-Tension
Bolts-Tightness
Engine
Gasoline-Amount
Safety Switch-Operation
Warning Decals-Legible
Tires, Flaps-Condition
Wires, Cables-Condition
Cutter Teeth-Sharpness

Maker
Model
CC Rating

Weight
Length
Width
Height
RPM Operating
Type of Fuel
Starting
Oil Sensor
Wheel Tire

Diameter
Thickness
Bearing
Cutter Wheel RPM
Drive

90kg
1605mm
680mm
1200mm
3600 rpm
Gasoline
Recoil
Yes
140/70-6

8.66” (220mm)
4.72” (12mm)
UCP205
2200 rpm/min
Direct Belt Drive

Centrifugal Clutch

113kg
1755mm
750mm
1200mm
3600 rpm
Gasoline
Recoil
Yes
145/70-6

9.45" (240mm)
4.72" (12mm)
UCP205
2500 rpm/min
Direct Belt Drive
17x1346Li V-belt
Centrifugal Clutch

Cutter Type
Steel Type
Steel Hardness
Weight
Length
Width
Tip Length

Wood
42CrMo
HRC40-42
1.59 lbs (0.72kg)
4-1/4" (10.8cm)
2-13/16" (7.1cm)
1-1/2" (3.8cm)

Wood
42CrMo
HRC40-42
1.59 lbs (0.72kg)
4-1/4" (10.8cm)
2-13/16" (7.1cm)
1-1/2" (3.8cm)

LONCIN G200F
G200F
200cc

LONCIN
G420F
390cc

Above Grade
Below Grade
Stump Diameter

9” (230mm)
8” (203mm)
20cm

10" (254mm)
9" (230mm)
No Limit

CAUTION:

IMPORTANT:

See manual

×

×

×

×

×

×

×

×

×

Installing Teeth

Maintenance Schedule

Содержание SGR1500


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды