MTI DAGE-MTI IR-1000 Скачать руководство пользователя | Manualshive

Страница: 7 / 20

background image

Video

This

‘

BNC

’

connector supplies video output of the

IR-1000

system. The signal is 1Vp-p terminated into 75

Ω

.

Be careful to avoid double termination of the output video,
which would result in incorrect video levels. Connect to a
monitor, computer or the

DAGE-MTI Investigater

as

required.

NOTE:

Do not use the

VIDEO OUT

connector on the camera

head. This will cause incorrect video levels to be sent to
the control and the signal at the camera head will be
double terminated.

Gate

This

‘

BNC

’

connector can be used to provide input of a

gate pulse in order to increase the sensitivity by inhibiting the
readout of the CCD's image and allowing light to gather in
the CCD for extended periods of time before readout.
Connect to a computer or the

DAGE-MTI Investigater

.

«
...
5
6
7
8
9
...
»

Содержание DAGE-MTI IR-1000





















Отзывы:

Нет отзывов

Похожие инструкции для DAGE-MTI IR-1000

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 13

Бренд: Panasonic Страницы: 26

Бренд: Abode Страницы: 5

Бренд: CADDX Страницы: 6

Бренд: Iget Страницы: 2

Бренд: OEM Optical Страницы: 25

Бренд: Dahua Страницы: 25

Бренд: SICK Страницы: 112

Бренд: Q-See Страницы: 13

ActiveEYE MS15A

Бренд: X10 Страницы: 2

Бренд: nedis Страницы: 40

HDW2831TM-AS-S2

Бренд: Dahua Technology Страницы: 17

Бренд: Lilin Страницы: 18

Бренд: Halo Smart Labs Страницы: 34

Бренд: Konig Security Страницы: 56

Бренд: Vitek Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды