MTI DAGE-MTI IR-1000 страница 19 Скачать руководство пользователя

Страница: 19 / 20

Limitations

1. This warranty is valid only if the malfunctioning unit is

returned to

DAGE-MTI

service depot. This warranty does

not cover on-location service. If warranty work is needed,
the following should be contacted:

DAGE-MTI,

INC.

Customer

Service

701

Roeske

Ave.

Michigan City, IN 46360

(219)

872-5514

Fax:

(219)

872-5559

[email protected]

2. This warranty does not cover:

a. Problems caused by or inflicted upon associated

equipment such as digitizing systems, video tape
recorders, cameras, microscopes, etc.

b. Damage caused by accident, misuse, improper power

source, fire, flood, lightning, other acts of God, war,
and repair or alteration by other than a

DAGE-MTI

authorized service organization.

c. Labor or incurred charges required in removing or

installing the Product, down time, failure of the
Product to perform properly, and any consequential
damages.

d. Transit damage.

3. Unit must be properly packaged (in original packing, if

possible) when being returned under warranty.

Содержание DAGE-MTI IR-1000





















Результаты поиска

Содержание DAGE-MTI IR-1000

Отзывы:

Похожие инструкции для DAGE-MTI IR-1000

Бренды по названию

Популярные бренды

MTI DAGE-MTI IR-1000, Руководство пользователя

Результаты поиска

Содержание DAGE-MTI IR-1000

Отзывы:

Похожие инструкции для DAGE-MTI IR-1000

Бренды по названию

Популярные бренды