MTHTrains Premier SD50 Diesel Engine Скачать руководство пользователя | Manualshive

Страница: 37 / 47

background image

Volume

Solution

The sounds seem distorted, especially
when the Horn or bell is activated.

No Sound

®

Proto-Sound 3.0 volume is set too high.
Turn the volume control knob on the bottom
of the chassis counter-clockwise to reduce
the volume.
Volume is set too low, adjust volume control
knob on the bottom of the chassis clockwise
to increase the volume or check connector to
speaker.

Lock-out

Solution

I can't get the engine to run after I power
up the transformer. It sits still with the
diesel and compressor sounds running.
The engine won't lock into forward,
neutral, or reverse.

The engine maybe locked into the neutral
position. Follow the procedure in the "Lock
into a Direction" section to unlock the
engine's direction. Engine speed must be
below 10 scale mph (approx. 10 volts or less
in conventional mode).

PFA

Solution

Once in PFA, the engine doesn’t go into
reverse.

When the PFA enters its last sequence
the bell automatically comes on

When PFA is enabled, pressing the
whistle and bell has no effect

I push the direction button but the next
sound clip in the sequence does not
play or the engine does not come out of
PFA after fourth press of the direction
button.

So that PFA effects can be as realistic as

®

possible, Proto-Sound 3.0 disables the
reversing unit whenever PFA is enabled.
This way the engine remains still at its stop
as the operator cycles through the PFA
sequences.
PFA is programmed to start ringing the bell
at that point. After approximately 12
seconds, it will automatically turn off.
Because PFA must control various effects in

®

each sequence, Proto-Sound 3.0 takes
control of these sound effects until you exit
PFA
Each PFA clip must play for aprox. 30
seconds before PFA will advance to the next
step in the PFA cycle. Wait at least 30
seconds in each PFA sound clip before
pressing the direction button.

Premier SD50 Diesel Engine

37

«
...
35
36
37
38
39
...
»

Содержание Premier SD50 Diesel Engine
















































Отзывы:

Нет отзывов

Похожие инструкции для Premier SD50 Diesel Engine

Бренд: Old School Model Works Страницы: 24

SM-79 Sparviero Exterior

Бренд: Eduard Страницы: 4

Operating Lighthouse

Бренд: Lionel Страницы: 8

Бренд: Lionel Страницы: 2

Бренд: Power Wheels Страницы: 32

Mario Kart Circuit Track Set

Бренд: Hot Wheels Страницы: 8

Pelican Aileron Wing

Бренд: CRASHTESTHOBBY.COM Страницы: 7

Spinning Tunes Music Player

Бренд: VTech Страницы: 10

Бренд: H-KING Страницы: 9

P-51D Mustang 40

Бренд: Kyosho Страницы: 18

Gravitrax Magnetic Cannon

Бренд: Ravensburger Страницы: 4

Zero Gravity Nano Wall Climber

Бренд: Air Hogs Страницы: 8

Бренд: PARKZONE Страницы: 19

EDGE 540 RACE 1200

Бренд: Hacker Страницы: 21

Little 834596 Little 834602

Бренд: BABY born Страницы: 68

Бренд: BABY born Страницы: 18

Бренд: Heng Long Страницы: 12

Бренд: Revell Control Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды