manualshive.com logo in svg

MTHTrains Premier SD50 Diesel Engine, Руководство оператора

Поделиться
Скачать
MTHTrains Premier SD50 Diesel Engine Скачать руководство пользователя страница 33

Maintenance

Lubricating and Greasing Instructions

The engine should be well oiled and greased in order to run properly.

Regularly lubricate all axles and pickup rollers to prevent squeaking.  
Use light household oil, such as that found in M.T.H.'s maintenance kit.  
Do not over oil.  Use only a drop on each pivot point.

The locomotive’s internal gearing was greased at the factory and should not need 
additional grease until after 50 hours of  operation or one year, whichever comes first. 
Remove the two grease port screws (two per gearbox). Use a grease tube dispenser and 
put a small amount (Approx. 1-2 mL.) of  lithium-based grease into each grease port. 
Replace the screws.

Lubricate the outside truck block idler and drive gears with grease.  Use the diagram 
shown in Figure 10 below as a guide and add grease to the points marked.

Figure 8: Lubrication Points

DO NOT

OVER OIL

DO NOT

OVER OIL

Figure 9: Body Removal Screw Locations and Motor Mounting Screws

Premier SD50 Diesel Engine

33

Figure 10: Greasing The Idler Gears

Grease Idler Gears (G)

Body Mount Screws

Grease Port Screws

Grease Port Screws

Lubricate All Wheel Axles (L)

Lubricate Pick Up Roller Axles (L)

Motor Mounting Screw

Содержание Premier SD50 Diesel Engine
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды