background image

CARE AND MAINTENANCE

HO Troubleshooting Guide

The following Guide will help you trouble shoot your M.T.H. HO 
powered car. This guide is broken up into the three operating modes of  
the powered car Analog DC, DCC, and DCS

Analog DC

When I apply power to the track my 
powered car doesn’t do anything. No 
lights, no sound, nothing.

Check to see if that section of track has 
power. Use a voltmeter or a lit passenger car.

Slide the powered car a couple of feet in 
either direction, you may have a bad track 
section.

Have you got that section electrically isolated 
with a toggle switch or other device?

I have no sound from my powered car, 
but my lights are on and it moves just 
fine.

There’s a crackling sound from my 
powered car

Check the volume pot on your powered car. 
Full CW = Max Volume

Check to see if a screw or some other 
material hasn’t lodged itself in the underside 
of the powered car body.

One of my lights is out.

None of my lights are on.

Most likely you had been running the 
powered car in DCC or DCS mode and 
toggled that light off. Put it back into one of 
those modes and turn that light back on. The 
powered car will remember that when you 
run it again in Conventional DC.

Could be the same reason as “One of my 
lights is out.”

Is the powered car getting power? Check to 
see if there is voltage on the track or move 
the powered car a few feet in either direction.

When I apply power to the track my 
powered car starts up (lights and 
sound) but it won't move

My powered car hesitates at slow 
speeds.

Lower the track voltage then raise it again. 
The powered car should start moving. If you 
apply greater than 9VDC quickly the engine 
will just sit there. Lowering it below 9VDC 
then raising it will get the engine moving. 

A powered car may do this right out of the box 
if it has not been lubricated. Follow the 
lubrication instructions. Now try to run it.

New powered cars may take a little bit to get 
everything running, even after they are 
lubricated. Be patient and let it run for a bit. It 
should clear up shortly after lubricating and 
running. 

Solution

Solution

Solution

Solution

Start-Up

Sound

Lights

Motion

M.T.H. HO Subway Car w/Proto-Sound 3.0

35

Содержание 80-2346-1










































Отзывы: