MSE Kestrel Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 31

MSE Kestrel Скачать руководство пользователя страница 25

SERVICING YOUR CENTRIFUGE

25

7 SERVICING YOUR CENTRIFUGE

7.1 Fault finding

Below is a list of faults and their possible solutions:

Fault

Solution

The centrifuge has no display

1. Check that the power cable is properly

plugged in and the mains is turned on

2. Check that the fuse hasn’t blown in the

plug or at the back of the unit

3. Ensure that the power switch is on

The centrifuge does not start

1. Check that the lid is closed properly
2. Ensure that the display is not flashing.

The centrifuge could be waiting for you to
input some parameters

The centrifuge starts, but it is not
accelerating properly

Make sure that the rotor is not overloaded
(the letter E will signify this on the display).
Turn centrifuge off and on again to clear the
error message.

Lid is not opening

Either the rotor is still running or there is a
failure in the lid lock. In the case of the
latter, contact MSE for repair.

If any problems persist, please contact your local MSE service agent

7.2 Opening the lid manually

It is possible to open the lid manually if there is a power failure or a fault develops
with the centrifuge. Please use the key provided with your centrifuge to press into the
hole on the right hand side. The lid should now open.

CAUTION:

Do not attempt to open the lid whilst the centrifuge is running

7.3 Safety inspections

From  the  point  of  view  of  operational  safety  the  centrifuge  has  to  be  subjected  to
inspection carried out by authorised service engineer or especially trained experts at
least  once  every  year  in  the  state  of  operational  readiness.  More  frequent
inspections  could  be  required  if  the  centrifuge  or  rotors  have  been  subjected  to  a
corrosion inducing environment. Results of inspections, repairs and tests have to be
recorded  and  kept  on  file.  This  instruction  manual  should  be  stored  near  the
centrifuge for reference.

«
...
23
24
25
26
27
...
»

Содержание Kestrel
































Отзывы:

Нет отзывов