MSD 6520 Скачать руководство пользователя страница 16

Страница: 16 / 24

INSTALLATION INSTRUCTIONS

AUTOTRONIC CONTROLS CORPORATION

• 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

GM IGNITIONS GM Large Cap HEI Distributors

There are three different large cap HEI distributors. To indentify

which of the following diagrams fit your specific application, remove

the distributor cap and rotor and locate the ignition module at the

base of the distributor. Count the number of terminals on both ends

of the module and follow the corresponding diagram. GM used 4,

5, and 7-pin modules in these distributors.
NOTE: Some 5-pin models may experience a hesitation or stall

on decceleration. If this occurs, contact MSD Tech Line

for the required bolt-in diode to correct the problem. MSD

Tech Line (915) 855-7123

GM IGNITIONS Wiring an HEI 4-pin Module (Magnetic Pickup Trigger).

PN 8860 HARNESS

WHITE

JUMPER

RED

KEY

CONNECTOR

TO ENGINE

GROUND

HEAVY RED

OR PINK WIRE

FROM CAR

WIRING HARNESS

WHITE

(NOT USED)

COVER WITH TAPE

ORANGE*

*ORANGE - CONNECTS TO B+
*BLACK - CONNECTS TO C-

BLACK*

PN 8861

HARNESS

CONDENSOR

GM-CABLE

HARNESS

GM MODULE

GROMMET

WIRE CLAMPS

REMOVE MODULE

INSTALL HARNESS

B+

GND

C-

MAGNETIC PICKUP

CONNECTOR

HEAVY RED

HEAVY BLACK

TO BATTERY

IGNITION

DIGITAL-6

PN 6520

PROGRAMMABLE

2 STAGE REV-LIMITER

STEP RETARD

CAPACITIVE DISCHARGE

IGNITION

Plus

NOTE: The GM Ignition Module and condensor are removed

and replaced with the MSD PN 8861 Harness.

Содержание 6520

























Результаты поиска

Содержание 6520

Отзывы:

Похожие инструкции для 6520

Бренды по названию

Популярные бренды

MSD 6520, Инструкция по установке

Результаты поиска

Содержание 6520

Отзывы:

Похожие инструкции для 6520

Бренды по названию

Популярные бренды