MSD 6520 Скачать руководство пользователя страница 24

Страница: 24 / 24

INSTALLATION INSTRUCTIONS

AUTOTRONIC CONTROLS CORPORATION

• 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

Limited Warranty

utotronic Controls Corporation warrants MSD Ignition products to be free from defects in material and

workmanship under normal use and if properly installed for a period of one year from date of purchase.

If found to be defective as mentioned above, it will be replaced or repaired if returned prepaid along with

proof of date of purchase. This shall constitute the sole remedy of the purchaser and the sole liability of

Autotronic Controls Corporation. To the extent permitted by law, the foregoing is exclusive and in lieu

of all other warranties or representations whether expressed or implied, including any implied warranty

of merchantability or fitness. In no event shall Autotronic Controls Corporation be liable for special or

consequential damages.

Service

In case of malfunction, this MSD component will be repaired free of charge according to the terms

of the warranty. When returning MSD components for service, Proof of Purchase must be supplied for

warranty verification. After the warranty period has expired, repair service is charged based on a minimum

and maximum charge.

Send the unit prepaid with proof of purchase to the attention of:

Customer Service Department,

Autotronic Controls Corporation, 12120 Esther Lama, Suite 114, El Paso, Texas 79936.

When returning the unit for repair, leave all wires at the length in which you have them installed. Be

sure to include a detailed account of any problems experienced, and what components and accessories

are installed on the vehicle.

The repaired unit will be returned as soon as possible after receipt, COD for any charges. (Ground

shipping is covered by warranty). All units are returned regular UPS unless otherwise noted. For more

information, call the MSD Customer Service Line (915) 855-7123. MSD technicians are available from

8:00 a.m. to 5:00 p.m. Monday - Friday (mountain time).

AUTOTRONIC CONTROLS CORPORATION

• 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

FRM23775

Revised 01/03

Printed In U.S.A.

AFTERMARKET COMPONENTS Wiring to a Pertronix Ignitor Kit

If you did not find a schematic to match your application, or if you need assistance, please

contact MSD Tech at (915) 855-7123.

RED

IGNITION KEY

ORANGE

BLACK

TO 12V

WHITE

BLACK

DISTRIBUTOR

WITH

PERTRONIX

MAGNETIC PICKUP

(NOT USED)

HEAVY RED

HEAVY BLACK

TO BATTERY

IGNITION

DIGITAL-6

PN 6520

PROGRAMMABLE

2 STAGE REV-LIMITER

STEP RETARD

CAPACITIVE DISCHARGE

IGNITION

Plus

Содержание 6520

























Результаты поиска

Содержание 6520

Отзывы:

Похожие инструкции для 6520

Бренды по названию

Популярные бренды

MSD 6520, Инструкция по установке

Результаты поиска

Содержание 6520

Отзывы:

Похожие инструкции для 6520

Бренды по названию

Популярные бренды