MQ Multiquip 24421 Скачать руководство пользователя страница 39

Страница: 39 / 70

PAGE 39 — JS36/30H55DE SERIES WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL — REV. #0 (5/02/16)

CHANGING BLADES

It is recommended that

ALL

the blades on the trowel

are changed at the same time. If only one or some of the

blades are changed, the machine will not finish concrete

consistently and the machine may wobble or bounce.
Perform the following procedure when changing blades:

Please note the blade orientation on the trowel arm before

removing.
1. Lift the trowel up, placing blocks under the main guard

ring to support it.

2. Remove the bolts and lock washers from all the

towel arms, and then remove the blades as shown in

Figure 57.

Figure 57. Blade Removal

3. Wire brush and remove all concrete and debris from

all surfaces of each of the four trowel arms. This is

important to properly seat the new blades.

4. Install the new blades, maintaining the proper blade

orientation for direction of rotation.

5. Reinstall the bolts and lock washers.

TROWEL

ARM

TROWEL

BLADE

ATTACHMENT

SCREWS

BLADE

ATTACHMENT

BAR

MAINTENANCE

TROWEL ARM REMOVAL

1. Each trowel arm is held in place at the spider plate

by a hex head bolt (zerk grease fitting) and a roll

pin. Remove both the hex head bolt and the roll

pin (Figure 58) from the spider plate.

2. Remove the trowel arm from the spider plate.
3. Should the trowel arm inserts ( bushing ) come out with

the trowel arm, remove the bushing from the trowel arm

and set aside in a safe place. If the bushing is retained

inside the spider plate, carefully remove the bushing

4. Examine the trowel arm bushing insert (Figure 58),

clean if necessary. Replace bushing if out of round

or worn.

Figure 58. Trowel Arm Removal

CAP

ZERK

GREASE

FITTING

BUSHING

SPIDER

PLATE

ROLL

TROWEL

ARM

Содержание 24421







































































Результаты поиска

Содержание 24421

Отзывы:

Похожие инструкции для 24421

Бренды по названию

Популярные бренды

MQ Multiquip 24421, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание 24421

Отзывы:

Похожие инструкции для 24421

Бренды по названию

Популярные бренды