MQ Multiquip 24421 Скачать руководство пользователя страница 36

Страница: 36 / 70

PAGE 36 — JS36/30H55DE SERIES WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL —

REV. #0 (5/02/16)

ENGINE OIL

1. Drain the engine oil when the oil is warm as shown in

Figure 48.

2. Remove the oil drain bolt and sealing washer and allow

the oil to drain into a suitable container.

3. Replace engine oil with recommended type oil as listed

in Table 4. For engine oil capacity, see Table 3 (engine

specifications).

DO NOT

overfill.

4. Reinstall drain bolt with sealing washer and tighten

securely.

Figure 48. Draining Engine Oil

SPARK PLUG

1. Remove and clean spark plug (Figure 49) with a wire

brush if it is to be reused. Discard spark plug if the

insulator is cracked or chipped.

2. Using a feeler gauge adjust spark plug gap to 0.028

~0.031 inch (0.7~0.8 mm).

3. Thread spark plug into cylinder hole by hand to prevent

cross-threading, then tighten securely.

NOTICE

Operating the engine with loose or damaged air cleaner

components could allow unfiltered air into the engine

causing premature wear and failure.

NOTICE

NEVER

use a spark plug of incorrect heat range.

MAINTENANCE

Figure 49. Spark Plug Gap

V-BELT

Visually examine the V-belt (Figure 50) and determine if it

is full of tiny cracks, frayed, has pieces of rubber missing,

is peeling or otherwise damaged.
Also, examine the belt and determine if it is

oil soaked

glazed

" (hard shiny appearance on the sides of the belt).

Either of these two conditions can cause the belt to run hot,

which can weaken it and increase the danger of it breaking.
If the V-belt exhibits any of the above wear conditions

replace the V-belt immediately.

Figure 50. V-Belt Inspection

GAP

.028 - .031 IN.

(0.7- 0.8 MM.)

GLAZED

OIL SOAKED

BROKEN

CORD FAILURE

CRACKS

MISSING RUBBER

SIDEWALL

WEAR

WORN BACK

COVER

Содержание 24421







































































Результаты поиска

Содержание 24421

Отзывы:

Похожие инструкции для 24421

Бренды по названию

Популярные бренды

MQ Multiquip 24421, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание 24421

Отзывы:

Похожие инструкции для 24421

Бренды по названию

Популярные бренды