MQ Multiquip 24421 Скачать руководство пользователя страница 21

Страница: 21 / 70

PAGE 21 — JS36/30H55DE SERIES WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL — REV. #0 (5/02/16)

Gearbox Oil

1. Determine if the gearbox oil is low by removing the oil

plug located on the side of the gearbox. (Figure 16) This

plug will be marked by the "check" decal. The correct

level of the lubrication oil should be to the bottom of

the fill plug.

Figure 16. Gearbox

2. If lubrication oil begins to seep out as the drain plug

is being removed, then it can be assumed that the

gearbox has a sufficient amount of oil.

3. If lubrication oil does not seep out as the drain plug

is being removed, fill with type ISO 680 (P/N 10139)

gearbox lubricant oil until the oil filler hole overflows.

V-Belt Check

A worn or damaged V-belt can adversely affect the

performance of the trowel. If a V-belt is defective or worn

simply replace the V-belt as outlined in the maintenance

section of this manual.

Belt Guard Check

Check for damage, loose or missing hardware.

Blade Check

Check for worn or damaged blades. Check to see if one

blade is worn out while the others look new. If this is

the case there could be a blade pitch problem. Refer to

the maintenance section of this manual for blade pitch

adjustment procedure. Replace any worn blades.

GEARBOX

OIL SIGHT GLASS/

FILL PLUG

DRAIN

PLUG

WARNING

NEVER

disable or disconnect the centrifugal safety

STOP

" switch. It is provided for operator safety. Injury

may result if it is disabled, disconnected or improperly

maintained.

Centrifugal Safety "STOP" Switch

This trowel has been equipped with a centrifugal safety

STOP

" switch (Figure 17). This switch should be tested

every time the engine is started.
The switching mechanism of this switch should operate

freely and should always be kept in this condition. With the

switch in the

OFF

position, the engine should not start or

run. The purpose of this switch is to stop the engine in a

runaway situation, (i.e. the operator releasing the handle

during operation).

Figure 17. Centrifugal Safety "STOP" Switch

OFF

CENTRIFUGAL

SAFETY “STOP”

SWITCH

INSPECTION

Содержание 24421







































































Результаты поиска

Содержание 24421

Отзывы:

Похожие инструкции для 24421

Бренды по названию

Популярные бренды

MQ Multiquip 24421, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание 24421

Отзывы:

Похожие инструкции для 24421

Бренды по названию

Популярные бренды