MPC UC006 Скачать руководство пользователя | Manualshive

Страница: 31 / 38

background image

30

Display Error Messages

Alarms and Warnings

In case of malfunction alarms and warning messages are indicated through the display.

Display Cause

Effect,

measurement

flashing display
(temperature
value)

Warning:
Over- undertemperature (limit
value +/- 2K from set point).

Thermoregulation continues.

F1-
flashing

malfunction sensor F1
broken or short circuit

Thermoregulation is inactive
(Pump off, compressor off,
heating off).

Please check sensor.

E1-
flashing

Inlet E1 indicates failure.
No release-signal, level-alarm.

Thermoregulation is inactive
(Pump off, compressor off,
heating off).
Check level.

Reset only possible if level ok.

E2-
flashing

Inlet E1 indicates failure.
Pump is running and
circulation is missing or Pump
is running and water pressure
is missing.

Thermoregulation is inactive
(Pump off, compressor off,
heating off).

Reset only possible if
disconnected from the power
supply.

E3-
flashing

Even though thermoregulation
is off, inlet E1 is indicating
circulation.

Thermoregulation is inactive
(Pump off, compressor off,
heating off).

Failure is being reset if inlet E1 is
open again in standby.

EP-
flashing

Loss of data in parameter
memory.

Thermoregulation is inactive
(Pump off, compressor off,
heating off).

Advice:
While error message is being indicated error and set point are displayed alternately.

«
...
29
30
31
32
33
...
»

Содержание UC006







































Отзывы:

Нет отзывов

Похожие инструкции для UC006

Бренд: Lawn Solutions Страницы: 14

Бренд: Daikin Страницы: 88

Бренд: Poulan Pro Страницы: 16

Garden Wizard 109312-01

Бренд: Remington Страницы: 44

AquaForce 30XAV 1050

Бренд: Carrier Страницы: 42

Бренд: Victory Страницы: 64

BIO MASTER 2200

Бренд: Stiga Страницы: 148

Бренд: Cub Cadet Страницы: 23

Бренд: Land Pride Страницы: 28

ENVISION 2 NKW Series

Бренд: Water Furnace Страницы: 32

Бренд: LEMKEN Страницы: 49

Бренд: Gardeo Страницы: 43

ActiveCore SKT series

Бренд: Skope Страницы: 82

Бренд: York Страницы: 32

ACTIVE AQUA AACH100

Бренд: Hydrofarm Страницы: 16

Бренд: HPG Страницы: 20

Бренд: Benassi Страницы: 8

Бренд: Hitecsa Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды