manualshive.com logo in svg

Moxa Technologies EDS-405, Руководство пользователя

Поделиться
Скачать
Moxa Technologies EDS-405 Скачать руководство пользователя страница 33

EDS-405 User’s Manual

 

Dip Switch Settings 

 

EDS-405 Series Dip Switches 

6

1

2

3

4

5

RM

P1

P2

P3

P4

P5

 

Set to ON: 

 

P1-P5

 

(Default is Off)

 

 

Enables the corresponding PORT Alarm. If the port’s link fails, the 
relay will form an open circuit and the fault LED will light up.

 

RM

 

(Default is Off) 

 

Enables this EDS-405 to be the Ring Master in a Turbo Ring 
topology, and enable the Turbo Ring break alarm. If the EDS-405 
is the Master of this Turbo Ring, and the Turbo Ring is broken, the 
relay will form an open circuit. 

Set to Off: 

 

P1-P5

 

Disables the corresponding PORT Alarm. The relay will form a 
closed circuit and the Fault LED will never light up. 

RM

 

Disables this EDS-405 from being the Ring Master in a Turbo Ring 
topology, and disables the Turbo Ring break alarm. If the EDS-405 
is the Master of this Turbo Ring, and the Turbo Ring is broken, the 
relay will form a closed circuit. 

 
 
 
 
 

 

4-8 

Содержание EDS-405









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды