Moxa Technologies AirWorks AWK-5222 Скачать руководство пользователя страница 67

Страница: 67 / 100

AWK-5222 User’s Manual

Other Console Configurations

3-49

Status

Wireless Status

The status for

802.11 info

parameters, such as Operation mode and Channel, are shown on the

Wireless Status

page. The status will refresh every 5 seconds if the

Auto refresh

box is checked.

Certain values for

802.11 info

may not appear with different operation modes. For example,

Current BSSID

and

RSSI

are not available in Redundant AP, AP, or Master modes.

It is helpful to use the continuously updated information option on this page, such as RSSI, to
monitor the signal strength of the AWK-5222 in Redundant Client, Client, or Slave modes.

Associated Client List

(for Redundant AP, AP, or Master mode only)

Associated Client List shows all the clients that are currently associated to a particular AWK-5222.
You can click

Select all

to select all the content in the list for further editing. You can click

Refresh

to refresh the list.

Содержание AirWorks AWK-5222




































































































Результаты поиска

Содержание AirWorks AWK-5222

Отзывы:

Похожие инструкции для AirWorks AWK-5222

Бренды по названию

Популярные бренды

Moxa Technologies AirWorks AWK-5222, Руководство пользователя

Результаты поиска

Содержание AirWorks AWK-5222

Отзывы:

Похожие инструкции для AirWorks AWK-5222

Бренды по названию

Популярные бренды