Moxa Technologies AirWorks AWK-5222 Скачать руководство пользователя страница 51

Страница: 51 / 100

AWK-5222 User’s Manual

Other Console Configurations

3-33

Packet Filters

The AWK-5222 includes various filters for

IP-based

packets going through LAN and WLAN

interfaces. You can set these filters as a firewall to help enhance network security.

MAC Filter

The AWK-5222’s MAC filter is a policy-based filter that can allow or filter out IP-based packets
with specified MAC addresses. The AWK-5222 provides 8 entities for setting MAC addresses in
your filtering policy. Remember to check the

Active

check box for each entity to activate the

setting.

Enable

Setting

Description

Factory Default

Enable Enables

MAC

filter

Disable

Disables MAC filter

Disable

Policy

Setting

Description

Factory Default

Only the packets fitting the entities on list
can be allowed.

Drop

Any packet fitting the entities on list will
be denied.

Drop

ATTENTION

Be careful when you enable the filter function:

Drop

+ “

entity on list is activated” = all packets are

allowed

Accept

+ “

entity on list is activated” = all packets are

denied

Содержание AirWorks AWK-5222




































































































Результаты поиска

Содержание AirWorks AWK-5222

Отзывы:

Похожие инструкции для AirWorks AWK-5222

Бренды по названию

Популярные бренды

Moxa Technologies AirWorks AWK-5222, Руководство пользователя

Результаты поиска

Содержание AirWorks AWK-5222

Отзывы:

Похожие инструкции для AirWorks AWK-5222

Бренды по названию

Популярные бренды