Moxa Technologies AirWorks AWK-5222 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 100

background image

AWK-5222 User’s Manual

Other Console Configurations

3-18

specified as 64/128 bits, which is actually a 40/104-bit secret key with a 24-bit initialization vector.
The AWK-5222 provides 4 entities of WEP key settings that can be selected to use with

Key index

.

The selected key setting specifies the key to be used as a

send-key

for encrypting traffic from the

AP side to the wireless client side. All 4 WEP keys are used as

receive-keys

to decrypt traffic from

the wireless client side to the AP side.

The WEP key can be presented in two

Key type

, HEX and ASCII. Each ASCII character has 8 bits,

so a 40-bit (or 64-bit) WEP key contains 5 characters, and a 104-bit (or 128-bit) key has 13
characters. In hex, each character uses 4 bits, so a 40-bit key has 10 hex characters, and a 128-bit
key has 26 characters.

Authentication type

Setting

Description

Factory Default

Open

Data encryption is enabled, but no
authentication.

Shared

Data encryption and authentication
are both enabled.

Open

Key type

Setting

Description

Factory Default

HEX

Specifies WEP keys in hex-decimal
number form

ASCII

Specifies WEP keys in ASCII form

HEX

Key length

Setting

Description

Factory Default

64 bits

Uses 40-bit secret keys with 24-bit
initialization vector

128 bits

Uses 104-bit secret key with 24-bit
initialization vector

64 bits

Key index

Setting

Description

Factory Default

1-4

Specifies which WEP key is used

Open

«
...
34
35
36
37
38
...
»

Содержание AirWorks AWK-5222





































































































Отзывы:

Нет отзывов

Похожие инструкции для AirWorks AWK-5222

Бренд: GE Страницы: 4

Бренд: Javad Страницы: 35

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

OCTOPUS 5TX-EEC

Бренд: Hirschmann Страницы: 6

MasterBus Tanklevel Interface

Бренд: Mastervolt Страницы: 8

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: Juniper Страницы: 7

Бренд: ActionTec Страницы: 115

DiamondLink 3201

Бренд: Patton Страницы: 12

Ezi-SERVOII EtherCAT TO

Бренд: Fastech Страницы: 108

Бренд: Global411 Страницы: 15

PacketMate 1000

Бренд: General DataComm Страницы: 20

Бренд: KYLAND Technology Страницы: 24

Бренд: Acces Страницы: 21

Бренд: Hame Страницы: 37

GigaSpire BLAST u4hm

Бренд: Calix Страницы: 45

Бренд: Valcom Страницы: 3

OfficeConnect 3CXSH654B

Бренд: 3Com Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды