Moxa Technologies Airworks AWK-3131A-M12-RCC Скачать руководство пользователя

Страница: 51 / 94

AWK-3131A-M12-RCC

Web Console Configuration

3-36

System Log

System Log Event Types

Detail information for grouped events is shown in the following table. You can check the box for Enable log to
enable the grouped events. All default values are enabled (checked). The log for system events can be seen in
Status



System Log.

System-related events

Event is triggered when…

System restart (warm start)

The AWK-3131A-M12-RCC is rebooted, such as when its settings
are changed (IP address, subnet mask, etc.).

Network-related events

Event is triggered when…

LAN link on

The LAN port is connected to a device or network.

LAN link off

The port is disconnected (e.g., the cable is pulled out, or the
opposing device shuts down).

Client joined/ left
(for AP/Master mode)

A wireless client is associated or disassociated.

WLAN connected to AP
(for Client/Slave mode)

The AWK-3131A-M12-RCC is associated with an AP.

WLAN disconnected
(for Client/Slave mode)

The AWK-3131A-M12-RCC is disassociated from an AP.

Config-related events

Event is triggered when…

Configuration Changed

A configuration item has been changed.

Configuration file import via Web Console The configuration file is imported to the AWK-3131A-M12-RCC.
Console authentication failure

An incorrect password is entered.

Firmware upgraded

The AWK-3131A-M12-RCC’s firmware is updated.

Power events

Event is triggered when…

Power 1/2 transition (On -> Off)

The AWK-3131A-M12-RCC is powered down in PWR1/2.

PoE transition (On -> Off)

The AWK-3131A-M12-RCC is powered down in PoE.

Power 1/2 transition (Off -> On)

The AWK-3131A-M12-RCC is powered via PWR1/2.

PoE transition (Off -> On)

The AWK-3131A-M12-RCC is powered via PoE.

DI events

Event is triggered when…

DI0/1 transition (On -> Off)

Digital Input 0/1 is triggered by on to off transition

DI0/1 transition (Off -> On)

Digital Input 0/1 is triggered by off to on transition

Содержание Airworks AWK-3131A-M12-RCC






























































































Результаты поиска

Содержание Airworks AWK-3131A-M12-RCC

Отзывы:

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Бренды по названию

Популярные бренды

Moxa Technologies Airworks AWK-3131A-M12-RCC, Руководство пользователя

Результаты поиска

Содержание Airworks AWK-3131A-M12-RCC

Отзывы:

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Бренды по названию

Популярные бренды