Moxa Technologies Airworks AWK-3131A-M12-RCC Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 94

background image

AWK-3131A-M12-RCC

Web Console Configuration

3-14

Security mode

Setting

Description

Factory Default

Open

No authentication

Open

WEP

Static WEP is used

WPA*

WPA is used

WPA2*

Fully supports IEEE802.11i with “TKIP/AES + 802.1X”

Open

For security reasons, you should NOT set security mode to Open System, since authentication and data
encryption are NOT performed in Open System mode.

WEP

According to the IEEE802.11 standard, WEP can be used for authentication and data encryption to maintain
confidentiality. Shared (or Shared Key) authentication type is used if WEP authentication and data encryption
are both needed. Normally, Open (or Open System) authentication type is used when WEP data encryption is
run with authentication.

When WEP is enabled as a security mode, the length of a key (so-called WEP seed) can be specified as 64/128
bits, which is actually a 40/104-bit secret key with a 24-bit initialization vector. The AWK-3131A-M12-RCC
provides 4 entities of WEP key settings that can be selected to use with Key index. The selected key setting
specifies the key to be used as a send-key for encrypting traffic from the AP side to the wireless client side. All
4 WEP keys are used as receive-keys to decrypt traffic from the wireless client side to the AP side.

The WEP key can be presented in two Key types, HEX and ASCII. Each ASCII character has 8 bits, so a 40-bit
(or 64-bit) WEP key contains 5 characters, and a 104-bit (or 128-bit) key has 13 characters. In hex, each
character uses 4 bits, so a 40-bit key has 10 hex characters, and a 128-bit key has 26 characters.

Authentication type

Setting

Description

Factory Default

Open

Data encryption is enabled, but without authentication

Open

Shared

Data encryption and authentication are both enabled.

«
...
27
28
29
30
31
...
»

Содержание Airworks AWK-3131A-M12-RCC































































































Отзывы:

Нет отзывов

Похожие инструкции для Airworks AWK-3131A-M12-RCC

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

Бренд: Paradyne Страницы: 22

Бренд: Keithley Страницы: 59

Бренд: SAF Страницы: 30

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

RIPWAVE 40-00460-00R

Бренд: Navini Networks Страницы: 35

PacketMate 1000

Бренд: General DataComm Страницы: 20

Бренд: Hamlet Страницы: 11

Бренд: Eagle Technology Страницы: 39

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

CNGE28FX4TX24MS2

Бренд: Comnet Страницы: 154

Бренд: Moxa Technologies Страницы: 8

ROADRECORDER 8400 NVR

Бренд: Safety Vision Страницы: 27

Бренд: Thecus Страницы: 148

Бренд: SMC Sierra Monitor Страницы: 43

Бренд: Planet Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды