Movincool 15SF Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

background image

Repair Section

32

7. TROUBLESHOOTING

7.1 Troubleshooting

• Before troubleshooting the system, the following inspection should be performed.

WARNING

• Disconnect power supply from the unit before performing any service. Beware that some

residual voltage may remain in the unit immediately after the power is disconnected.

(1) Inspection of power supply

• Check the voltage of the power source.

- 1 Phase, 230 V, 50 Hz

• Test the power supply circuit breaker and residual current device (RCD) before connecting the

unit and then at least once a month during operation.

(2) Inspection of air filters

• Remove the air filters and check the filter elements. If the elements are dirty, remove dust with

a vacuum cleaner, or rinse in cold or lukewarm water. If the elements are extremely dirty, wash
with a neutral detergent.

• Affer the filter elements have been cleaned, rinse with clean running water, allow to dry, then

reinstall.

(3) Inspection of drain tank

• Make sure the tank is fully drained.

The following pages (page 33 to 37) are self-diagnostic codes and troubleshooting information.

«
...
30
31
32
33
34
...
»

Содержание 15SF

































































Отзывы:

Нет отзывов

Похожие инструкции для 15SF

Бренд: Taylor Страницы: 58

Бренд: Taylor Страницы: 57

Бренд: ICELAND Страницы: 24

Бренд: Ariston Страницы: 24

Бренд: True Страницы: 2

Бренд: Linea 2000 Страницы: 80

Бренд: EAS Electric Страницы: 56

Бренд: Frigomat Страницы: 151

Бренд: Vestfrost Страницы: 109

VF 11186 NoFrost

Бренд: Vestfrost Страницы: 116

Бренд: Aspes Страницы: 68

Бренд: Danby Страницы: 6

Бренд: Danby Страницы: 12

Бренд: Danby Страницы: 20

Бренд: Danby Страницы: 28

Бренд: Continental Refrigerator Страницы: 2

Designer Line DL1FI-SS-E

Бренд: Continental Refrigerator Страницы: 2

Бренд: Continental Refrigerator Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды