Movincool 15SF Скачать руководство пользователя страница 41

Страница: 41 / 64

Repair Section

7.8 Auxiliary Relay Inspection

• Check the continuity across the terminals 13

and 14, when the test button is depressed as
well as when released.

(Reference)

7.9 Full Drain Switch Inspection

• Depress the full drain switch to check for

continuity. If there is no continuity, replace the
switch.

• Normally: Continuity across 1 and 2.
• Switch Depressed: Continuity across 1 and 3.

7.10 Thermistor Inspection

• Use an ohmmeter to check the resistance

across the 2-pin connector at normal
temperature (25 °C).

Terminals

State of Reset Switch

Continuity

13-14

Depressed

Continuity

Released

No continuity

23-24

Depressed

Continuity

Released

No continuity

33-34

Depressed

Continuity

Released

No continuity

43/41-

44/42

Depressed

Continuity

Released

No continuity

Type

Specification

Characteristic

Evaporator Inlet Air

Thermistor (RTS)

5 k ohm at 25 °C

Freeze Protection Thermistor

(CTS)

5 k ohm at 25 °C

I001694

I001745

Full Drain Switch

Relay
Board
(CN16)

COM

C (1)

NC (2)

I001695

Содержание 15SF

































































Результаты поиска

Содержание 15SF

Отзывы:

Похожие инструкции для 15SF

Бренды по названию

Популярные бренды

Movincool 15SF, Руководство по обслуживанию

Результаты поиска

Содержание 15SF

Отзывы:

Похожие инструкции для 15SF

Бренды по названию

Популярные бренды