Mountain Models Magpie AP Скачать руководство пользователя

Страница: 2 / 19

Mountain Models Magpie

Before You Begin

Before you begin building your Magpie, make sure you read and understand all of the

instructions thoroughly.

Additionally, you will need to have the following items.

What You Will Need

•

Smooth and flat work surface

•

Wax paper to protect the plans

•

Thin Cyanoacrylate (CA) glue

•

Foam Safe Glue – 5 minute epoxy, white glue, or foam safe medium CA. We
recommend a tube of 5 minute epoxy.

•

Hobby knife with #11 blades

•

Needle nose pliers

•

Wire cutters

•

Sanding block with 200 grit sandpaper

•

2" packing tape or wing tape for covering the wings and fuselage

•

3M77 spray adhesive

•

4- or 5-channel radio rudder/elevator/throttle/camera shutter/camera tilt (optional).

•

GWS EPS400C-E motor or brushless motor such as the Feigao 1308416L

•

3 micro servos (4 if you are using the camera tilt option)(we recommend the Hitec

HS55, GWS Pico, or Naro)

•

Electronic Speed Control (ESC) capable of handling at least 15 amps

•

1000mAH or higher 2s or 3S LiPoly battery is recommended for weight savings

Parts List

Quantity

Description of Part

Wood

1/32” Laser cut plywood sheet

1/32” Laser cut plywood wing spar

1/16” Laser cut plywood sheet

1/8” Laser cut plywood sheet

Foam

2 Wing

sections

2 Fuselage

sections

5 Depron

tail

surfaces

Additional Parts

1/8” round x 7 3/16” hardwood dowel

1/8” round x 2.5” hardwood dowel

6” heat shrink tubing

6” Velcro strip for mounting the battery

180” plastic strapping

1/32” x 18” thin music wire for the pushrods

Bent aluminum landing gear

1-3/4” Dubro SL tires

Содержание Magpie AP




















Результаты поиска

Содержание Magpie AP

Отзывы:

Похожие инструкции для Magpie AP

Бренды по названию

Популярные бренды

Mountain Models Magpie AP, Руководство по сборке

Результаты поиска

Содержание Magpie AP

Отзывы:

Похожие инструкции для Magpie AP

Бренды по названию

Популярные бренды