Mountain Models Magpie AP страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 19

background image

Mountain Models Magpie

8

4.

Attach the assembly from step 3 to one of the sides of the camera mount base as in the

photo. Make sure they are seated well, then glue all the joints with thin CA.

5.

Glue the other camera mount base side to the front plate and landing gear. Glue with thin

CA.

6.

Attach the rear camera mount base plate. Again, note that the blind nut orientation is

coming from the rear side. Glue with thin CA and flow more thin CA into all the joints—
this is the mount that will hold your expensive camera, so make sure it is secure.

NOTE:

Do not try to insert the camera mount base assembly into the foam of the fuselage until the glue

is completely dry, as thin CA will melt the EPS foam.

Assemble the Fuselage

You will assemble the fuselage by first gluing the two fuselage halves together, adding four
pieces of strapping plastic for reinforcement, inserting the camera mount base/wing saddle

assembly, sanding to shape, adding servo mounting plates, then taping the fuselage. Follow

along carefully as there are a few critical steps along the way.

1.

Glue the two fuselage halves together. Note that the rear section of the fuselage is

slanted down to the tail on top and flat on the bottom. Place a protective wedge that

came with the rear fuselage under the rear half to help make the two sections meet. You

«
...
6
7
8
9
10
...
»

Содержание Magpie AP




















Отзывы:

Нет отзывов

Похожие инструкции для Magpie AP

Бренд: F-One Страницы: 11

Бренд: Kavan Страницы: 24

Бренд: Ozone Страницы: 12

Бренд: Thoma Modelltechnik Страницы: 33

Бренд: MINICRAFT Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды