manualshive.com logo in svg

Mountain Models Magpie AP, Руководство по сборке

Поделиться
Скачать
Mountain Models Magpie AP Скачать руководство пользователя страница 18

Mountain Models Magpie 

18

5. 

We need to make a pushrod that can switch between two holes, depending on what side of 

the plane the camera is mounted.  The cradle will be set up to rotate 90 degrees and we 
want to select between horizontal from the right to straight down, or straight down to 

horizontal on the left.  You will glue the servo to the side of the fuselage so that the 

pushrod is pinched between the servo control horn and the 1/8” ply you glued in step 3. 

This makes it easy to pull the pushrod out of the hole in the cradle to switch holes, but the 
pressure on the servo arm will keep the pushrod in place during flight. 

6. 

 I find it advisable to wrap the servo in wing tape before gluing.  Roughen the tape on the 

servo and the fuselage to get a good glue bond between the two tape surfaces. 

 

 

 

7. 

Once you are satisfied with the movement of the cradle, apply a drop of thin CA to the 

pushrod to prevent it from slipping. 

8. 

I control my tilt with my flap knob and activate my shutter with my rudder stick.  My 

rudder is on my aileron stick. 

Finishing the Kit 

Well, you’re almost there…the end is in sight; just a few more steps and you can go flying, 

assuming the weather is cooperating. 

Содержание Magpie AP




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды