Mountain Models Magpie AP Скачать руководство пользователя

Страница: 16 / 19

Mountain Models Magpie

Install the Wing

1. Slide the two 1/8” x 2.5” dowels through the holes in one wing mount, through the

fuselage, and through the hole in the other wing mount. You will probably not need

to glue the dowels in place.

2. Set the wing on the mount and secure it with 6 rubber bands.

Install the Motor

You will need:

•

Motor/gearbox (not provided with kit)

•

#2 x 3/8” motor retaining screw (Bagged Parts)

Installing the Motor

Slide the motor over the motor mount stick and slide the motor as far back as possible.

Using a small drill bit or the tip of an xacto, start a hole in the side of the gearbox for the

motor retaining screw. Screw in the motor retaining screw and then install the propeller.

If you are using a GWS propeller, make sure the print on the blades is facing

forward.

Содержание Magpie AP




















Результаты поиска

Содержание Magpie AP

Отзывы:

Похожие инструкции для Magpie AP

Бренды по названию

Популярные бренды

Mountain Models Magpie AP, Руководство по сборке

Результаты поиска

Содержание Magpie AP

Отзывы:

Похожие инструкции для Magpie AP

Бренды по названию

Популярные бренды