background image

B

7

Revision date: 09/10/2016

        7. Adjusting Your Tilt:

 To adjust the tilt position on your display you will need to loosen the knob on 

the side of each one of the arm brackets, set the desired tilt and then tighten the arms back up. You can 
loosen the screws slightly so that it will still hold while you adjust your tilt, once you have set the desired 
angle of tilt you can then fully tighten the knobs.

Section 2: Concrete and Masonry Installation:

        1.  Mark  Installation  Points: 

Once  you  have  selected 

the  location  you  want  the  mount  to  be,  mark  the  exact 
location  where  the  anchors  and  lag  bolts  will  be  installed. 
Next, pre-drill the holes using a masonry 10mm drill bit to a 
depth  of  2”  then  insert  the  supplied  anchors.  If  you  do  not 
have a metric drill bit a 3/8" drill bit will work.

        Drilling  Into  Concrete:

  When  drilling  into  concrete  or 

masonry, you have to use a special masonry drill bit which 
you  can  purchase  at  your  local  hardware  store,  using  a 
standard  drill  bit  will  not  penetrate  the  concrete  and  it  will 
just  dull  your  drill  bit.  It  is  not  recommended  to  drill  and 
mount into concrete block or mortar joints. If mounting into 
concrete  or  masonry  we  recommend  using  all  of  the 
supplied  plastic  anchors  and  lag  bolts  for  maximum 

support. The supplied plastic anchors are rated for use up to 165LBS, but if you prefer you can go to your 
local hardware store and purchase metal concrete anchors. 

2. Attaching The Mount to Your Wall:

Once  the  holes  are  pre-drilled  and  all  plastic 
anchors  are  inserted,  affix  the  wall  plate  with  the 
four supplied lag bolts into the wall.

At this point you can proceed back to Step 4 in the wood stud installation section to complete your 
Concrete/Masonry installation.

ATTENTION:

This mount must be installed using the supplied hardware with all four lag bolts screwed into your stud. If 
you  are  mounting  into  concrete  or  mortar,  all  four  anchors  and  screws  must  be  used  for  maximum   
support.  The  mount  cannot  be  held  liable  for  damage  to  the  wall,  Tv’s,  Furniture,  or  Fixtures  after 
installing this item.

Содержание MI-2171L








Отзывы: