Motortech MIC6 Скачать руководство пользователя страница 8

Status-Bits EN

P920380 - MIC6

Revision: 33493

Pickup Status

error.

3..8 reserved (for future use)

-

-

9

No Signal

i

No signal detected on this input although it has been 
configured.

10

reserved

-

-

11

reserved

-

-

12

Polarity Detection Failed

i

Polarity detection failed.

13

Wrong Polarity

i

The input signal has the wrong polarity.

This bit is not reset until the next synchronization.

14

reserved

-

-

15

reserved

-

-

16

No Index Mark Found

i

The index mark for N+1, N-1, … was not found, i.e. the 
input has been configured for N+1 but actually reads a N 
disc.

17

Wrong Number of Events

i

The number of events counted does not match the 
number of events configured/expected.

18

Missing Signal

i

An expected signal was missing. For example the trigger 
period increased by more than 50%.

19

Faulty Signal

i

An unexpected signal was detected. For example the 
trigger period decreased to less than 50%.

20

Missing Index Mark

i

A previously checked index mark was missing. For 
example the additional pin of a N+1 disc is missing during
operation.

21

Faulty Index

i

The index derived from this input was too early in relation 
to another signal. For example the reset signal of a 3PU 
system was too early or there was noise on the reset 
signal.

22

Missing Index

i

The index derived from this input was too late in relation 
to another signal or it was missing. For example the CAM
signal was expected before a reset signal but missing.

23..
32

reserved (for future use)

-

-

6

Copyright

Weitergabe sowie Vervielfältigung dieser Unterlage, ihre Verwertung und Mitteilung ihres Inhalts ist nicht 
gestattet, außer es wird ausdrücklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle 
Rechte für den Fall der Patenterteilung oder Gebrauchsmustereintragung vorbehalten.
Dieses Dokument liegt in seiner aktuellen Version bei der Projektleitung und kann von dort angefordert 
werden. Alle Änderungen werden an oben genannte Unterzeichner weitergeleitet.

The reproduction, distribution and utilization of this document as well as the communication of its contents to 
others without explicit authorization is prohibited. Offenders will be held liable for the payment of damages. 
All rights reserved in the event of the grant of a patent or utility model.
The project management owns a current version of this document where it can be requested. All changes 
will be forwarded to the undersigned mentioned above.

8 / 8

Содержание MIC6









Отзывы: