Motorola Vanguard 100 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 94

background image

Introduction to Vanguard IP and LAN Feature Protocols

1-3

T0100-01, Revision B

Release 5.4

IP and LAN Protocol Support

Physical LAN Connectivity

Introduction

The Vanguard products offer serial interfaces for connection to Ethernet and Token
Ring LAN.

Ethernet 802.3

Vanguard Ethernet functionality complies with the IEEE 802.3 specifications and
provides Transparent Bridging to transport many different protocols over the Wide
Area Network (WAN) to remote destinations. Supported protocols include:

• Novell Netware

• DECnet

• Banyan Vines

Token Ring 802.5

Vanguard Token Ring LAN functionality complies with the IEEE 802.5
specifications and provides Source Route Bridging to transport many different
protocols over the Wide Area Network (WAN) to a remote destination. Some of the
supported protocols include:

• Novell NetWare

• SDLC Cluster Controller

• IBM PC LAN

• NetBIOS

• IBM 3270 Emulation 3.0

• IBM APPC

See the IEEE 802.5 specification for additional details on Token Ring functionality.

«
...
7
8
9
10
11
...
»

Содержание Vanguard 100































































































Отзывы:

Нет отзывов

Похожие инструкции для Vanguard 100

Бренд: GE Страницы: 93

Бренд: Acconeer Страницы: 32

Бренд: Salusfin Страницы: 6

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

NI WLS/ENET-9163

Бренд: National Instruments Страницы: 36

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: peplink Страницы: 2

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: Netis Страницы: 16

InnoMedia MTA 3328-2R

Бренд: VoiceLine Страницы: 18

Бренд: Crystal Vision Страницы: 54

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

Бренд: Multitech Страницы: 81

Бренд: Idis Страницы: 16

Бренд: ZIMO Страницы: 13

Бренд: Zoom Страницы: 31

SFD-2 MkIII Jumper

Бренд: Anthem Audio Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды