Motorola PRO Series, Подробное руководство по обслуживанию

Страница: 74 / 686

Section 3: 1-16 Controller Board Audio and Signaling Circuits
Section : 6881091C63-F
SQ DET is used to determine all audio mute / unmute decisions except for Conventional Scan. In
this case CH ACT is a pre-indicator as it occurs slightly faster than SQ DET.
2.4.2 Audio Processing and Digital Volume Control
The receiver audio signal enters the controller section from the IF IC on DISC AUDIO. The signal is
DC coupled by R0228 and enters the ASFIC CMP via the DISC pin U0221-2.
Inside the ASFIC CMP, the signal goes through 2 paths in parallel, the audio path and the PL/DPL
path.
The audio path has a programmable amplifier, whose setting is based on the channel bandwidth
being received, then a LPF filter to remove any frequency components above 3000Hz and then an
HPF to strip off any sub-audible data below 300Hz. Next, the recovered audio passes through a
de-emphasis filter if it is enabled (to compensate for Pre-emphasis which is used to reduce the
effects of FM noise). The IC then passes the audio through the 8-bit programmable attenuator
whose level is set depending on the value of the volume control. Finally the filtered audio signal
passes through an output buffer within the ASFIC CMP. The audio signal exits the ASFIC CMP at
pin AUDIO (U0221-41).
The µP programs the attenuator, using the SPI BUS, based on the volume setting. The minimum /
maximum settings of the attenuator are set by codeplug parameters.
Since sub-audible signaling is summed with voice information on transmit, it must be separated from
the voice information before processing. Any sub-audible signaling enters the ASFIC CMP from the
IF IC at DISC U0221-2. Once inside it goes through the PL/DPL path. The signal first passes
through one of 2 low-pass filters, either PL low-pass filter or DPL/LST low-pass filter. Either signal is
then filtered and goes through a limiter and exits the ASFIC CMP at LSIO (U0221-18). At this point
the signal will appear as a square wave version of the sub-audible signal which the radio received.
The µP U0101-80 will decode the signal directly to determine if it is the tone / code which is currently
active on that mode.
2.4.3 Audio Amplification Speaker (+) Speaker (–)
The output of the ASFIC CMP’s digital volume pot, U0221-41 is routed through DC blocking
capacitor C0265 to a buffer formed by U0211-1. Resistors R0265 and R0268 set the correct input
level to the audio PA (U0271). This is necessary because the gain of the audio PA is 46 dB, and the
ASFIC CMP output is capable of overdriving the PA unless the maximum volume is limited. Resistor
R0267 and capacitor C0267 increase frequency components below 350Hz.
The audio then passes through R0269 and C0272 which provides AC coupling and low frequency
roll-off. C0273 provides high frequency roll-off as the audio signal is routed to pins 1 and 9 of the
audio power amplifier U0271.
The audio power amplifier has one inverted and one non-inverted output that produces the
differential audio output SPK+ / SPK- (U0271-4/6). The inputs for each of these amplifiers are pins 1
and 9 respectively; these inputs are both tied to the received audio. The audio PA’s DC biases are
not activated until the audio PA is enabled at pin 8.
The audio PA is enabled via the ASFIC CMP (U0221-38). When the base of Q0271 is low, the
transistor is off and U0271-8 is high, using pull up resistor R0273, and the audio PA is ON. The
voltage at U0273-8 must be above 8.5 VDC to properly enable the device.