Motorola CDR500, Руководство по программированию

Страница: 95 / 104

March, 2001 6864110R66-O
13-11
CDR500 & CDR700 Repeater Service Manual Troubleshooting
Table 13-8. Troubleshooting for ZR340 Controller
Symptom Problem(s) Possible Solution(s)
1. No “Rx” LED indication when
signal is received. 1a. Improper programming of ac-
cessory connector of receive ra-
dio.
1b. Loose or bad repeater cable to re-
ceive radio.
1c. JP7 and/or JP8 in ZR340 in
wrong position(s).
1a. Reprogram:
• Pin 4 (“CSQ Detect,” active
“High”)
• Pin 12 (“PL and CSQ Detect/
Talkgroup Detect,” active
“Low”).
1b. Check cable connections and re-
place cable, if necessary.
1c. Check position(s) and correct.
2. No “Tx” LED indication in re-
peater mode when properly
identified signal is received or
transmit radio does not key. 2a. Receive radio not programmed
for proper TPL/DPL code.
2b. Improper programming of ac-
cessory connector of receive ra-
dio.
2c. Incorrect programming of
ZR340.
2d. Improper programming of ac-
cessory connector of transmit ra-
dio.
2e. Pin 3 of transmit radio accessory
connector programmed incor-
rectly.
2f. Transmit frequency “busy.”
2a. Reprogram correct “Rx Squelch
Code.”
2b. Reprogram:
• Pin 4 (“CSQ Detect,” active
“High”)
• Pin 12 (“PL and CSQ Detect/
Talkgroup Detect,” active
“Low”).
2c. Use DTMF to select half-duplex
and repeater enabled (40# then
18#).
2d. Reprogram:
• Pin 4 (“CSQ Detect,” active
“High”)
• Pin 12 (“NULL,” active Low”).
2e. Reprogram pin 3 for “External
Mic PTT”.
2f. Wait for channel to clear.
3. Some field radios can not access
telephone. 3a. Incorrect setup of ZR340.
3b. Incorrect programming of field
radios.
3c. Incorrect access codes being sent
by field radios.
3d. Low DTMF deviation in field ra-
dios.
3a. Check “Rx” (receive) control set-
ting of ZR340.
3b. Reprogram field radios.
3c. Reprogram field radios or reed-
ucate radio users.
3d. Readjust DTMF deviation for
60% to 70% rated system.
4. Transmit radio keys but low or
no audio is transmitted. 4a. “Rx” and/or “Tx” control(s) of
ZR340 not adjusted correctly.
4b. “Accessory Mic Gain” set too
low in transmit radio.
4c. “Ext PTT Audio” source incor-
rect.
4a. Adjust “Rx” and/or “Tx” con-
trol(s) on ZR340.
4b. Reprogram “Accessory Mic
Gain”.
4c. Reprogram for “Ext Mic Audio.
5. No “Phone” LED indication
when attempting to access tele-
phone line (PSTN). 5a. Improper programming of field
radios or ZR340.
5b. Wrong access code transmitted
by field radios.
5a. Reprogram field radios or
ZR340.
5b. Reprogram field radios or reed-
ucate radio users.
6. ZR340 will not pulse dial PSTN
from field unit DTMF. 6a. Not programmed for pulse dial.
6b. Too much time has elapsed be-
tween digits.
6c. What is “pulse dial”?
6a. Reprogram the ZR340.
6b. Do not allow more than 5 sec-
onds between digits.
6c. One step above calling “Ernes-
tine”.
7. Unreliable dialing or misdialed
numbers. 7a. Low DTMF deviation of field ra-
dios.
7b. Incorrect setting of “Rx” control
on ZR340.
7a. Readjust DTMF deviation for
60% to 70% of rated system devi-
ation.
7b. Reset “Rx” control on ZR340.