MOTO GUZZI V85 E4 Скачать руководство пользователя

Страница: 95 / 108

Checking the connecting rod

•

Check using a micrometer the measure of the connecting rod pin orthogonal axes an in the

working area of the small ends, check the measure of the small ends seats on the timing

system side and on the flywheel side.

•

Assemble the connecting rod without small ends and tighten the connecting rod screws to

the prescribed torque. Measure the outer diameter of small ends seats with a dial gauge

graduated in hundredths of a millimetre and the thickness of both small ends with a round

tip micrometer.

•

Check the bushings pressed in the small end of the connecting rod for notches due to seizing

or deep scoring; replace as required.

ONNECTING

ROD

CHECK

Specification

Desc./Quantity

Diameter connecting rod head seat (MAXIMUM WEAR VAL-

UE)

43.67 mm (1.7193 in)

Thickness of connecting rod head small ends (MINIMUM

WEAR VALUE)

1.807 mm (0.0711 in)

Diameter of the small end with pressed and bored bushing

(MAXIMUM WEAR VALUE)

20.015 mm (0.7880 in)

Assembling the connecting rod

•

Before assembly, take careful note of the reference markings and the correct direction of

installation.

•

There are two available models of connecting rods and the points where the laser marks or

incisions are shown on the crankshaft may differ depending on the engine output:

A/blue - B/white

(white or blue dot in the zone indicated by the letter

in the drawing) to be assembled

correctly with the crankshaft, available in two models

A/blue - B/white

(laser mark or white or blue dot

in the zone indicated by the letter

in the drawing) for the crankpin, using the appropriate bushing.

Engine V85 E4

Engine

ENG - 95

Содержание V85 E4













































































































Результаты поиска

Содержание V85 E4

Отзывы:

Похожие инструкции для V85 E4

Бренды по названию

Популярные бренды

MOTO GUZZI V85 E4, Руководство по обслуживанию станции

Результаты поиска

Содержание V85 E4

Отзывы:

Похожие инструкции для V85 E4

Бренды по названию

Популярные бренды