MOTO GUZZI V85 E4 страница 71 Скачать руководство пользователя

Страница: 71 / 108

Adjusting valve clearance

•

Bring the piston of the left cylinder to

top dead centre making sure that the

reference mark on the crankshaft gear

and on the timing system shaft are

aligned.

NOTE

PROCEDURE VALID ONLY FOR E4 VEHICLES

•

Bring the piston of the left cylinder to

top dead centre

•

Check that the punching of the crank-

shaft pinion (1) is aligned with the

punching on the timing system sprock-

et (2). The punching on the timing sys-

tem sprocket can be viewed through

the hole of the chain guide cap

NOTE

PROCEDURE VALID ONLY FOR E5 VEHICLES

•

Use a feeler gauge to check that the

clearance between the valve and the

set screw corresponds with the indica-

ted values. The corresponding intake

and outlet valve clearances are differ-

ent than what is indicated below, pro-

ceed with adjusting them.

Characteristic

Intake valve clearance

0.10 mm (0.0039 in)

Exhaust valve clearance

0.15 mm (0.0059 in)

Engine V85 E4

Engine

ENG - 71

Содержание V85 E4













































































































Результаты поиска

Содержание V85 E4

Отзывы:

Похожие инструкции для V85 E4

Бренды по названию

Популярные бренды

MOTO GUZZI V85 E4, Руководство по обслуживанию станции

Результаты поиска

Содержание V85 E4

Отзывы:

Похожие инструкции для V85 E4

Бренды по названию

Популярные бренды