MOTO GUZZI V85 E4 страница 80 Скачать руководство пользователя

Страница: 80 / 108

•

Position the three fixing screws of the

timing gear and tighten to the prescri-

bed torque.

NOTE

ONLY FOR E4 VEHICLES

•

Position the tone wheel and after in-

serting the fixing screw with washer,

tighten to the prescribed torque.

NOTE

ONLY FOR E4 VEHICLES

•

Fit the front chain guide on the timing

system sprocket and then insert the

three fixing screws and tighten them to

the recommended torque.

NOTE

ONLY FOR E5 VEHICLES

•

Fit the bulkhead on the camshaft, fit the

fixing screw and tighten it to the rec-

ommended torque.

NOTE

ONLY FOR E5 VEHICLES

•

Turn the crankshaft manually checking that there is no jamming. If jamming does occur,

repeat the timing operation

Cylinder-piston assembly

Engine

Engine V85 E4

ENG - 80

Содержание V85 E4













































































































Результаты поиска

Содержание V85 E4

Отзывы:

Похожие инструкции для V85 E4

Бренды по названию

Популярные бренды

MOTO GUZZI V85 E4, Руководство по обслуживанию станции

Результаты поиска

Содержание V85 E4

Отзывы:

Похожие инструкции для V85 E4

Бренды по названию

Популярные бренды