MOTO GUZZI V7 CLASSIC Скачать руководство пользователя страница 59

Страница: 59 / 134

•

Blue (cable harness side): Ground connection

•

Green/brown (cable harness side): voltage 12V

DIAGNOSIS

•

The vehicle with clutch pulled, gear engaged and side stand retracted does not start (side

stand switch always open): check continuity of the green/brown cable between PIN 2 of

diode 40 (wiring diagram) and the corresponding PIN of the sensor connector on the cable

harness side. If there is not continuity, restore cable harness; if there is continuity, with side

stand retracted, check continuity between the 2 PINS of the sensor. If there is not, replace

the sensor; if there is continuity, check continuity to ground connection of the blue cable on

the connector (cable harness side).

•

The vehicle, with clutch operated and gear engaged, starts but with the side stand extended:

disconnect the sensor connector and check that, with side stand extended, there is not

continuity between the 2 PINS. If there is continuity, replace the sensor; if there is not con-

tinuity, disconnect diode 40 and check ground insulation of the green/brown cable between

sensor and diode

Bank angle sensor

Function

it tells the vehicle position to the control unit.

Operation / Operating principle

When the sensor is inverted, the circuit is closed

to ground: when the Marelli control unit detects this

ground, it deactivates the circuit of the fuel pump

and the engine start-up circuit, via the injection re-

lay.

Level in wiring diagram:

Start-up enabling

switches.

Location:

•

under the saddle, rear section

•

connector: near the sensor

Electrical characteristics:

•

Sensor in vertical position: open circuit

(resistance: 62 kOhm)

•

Sensor inverted: closed circuit (resist-

ance lower than 0.5 kOhm)

Pin-out:

V7 Classic

Electrical system

ELE SYS - 59

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание V7 CLASSIC







































































































































Результаты поиска

Содержание V7 CLASSIC

Отзывы:

Похожие инструкции для V7 CLASSIC

Бренды по названию

Популярные бренды

MOTO GUZZI V7 CLASSIC, Руководство по обслуживанию

Результаты поиска

Содержание V7 CLASSIC

Отзывы:

Похожие инструкции для V7 CLASSIC

Бренды по названию

Популярные бренды