MOTO GUZZI V7 CLASSIC Скачать руководство пользователя страница 56

Страница: 56 / 134

two cable terminals. If there is no continuity, restore the cable harness; if there is cable

continuity, with key set to ON, check the cable earth insulation (from coil connector or control

unit connector). If not OK, restore the cable harness.

Engine oil pressure sensor

Function:

it indicates the instrument panel if there

is enough oil pressure 0.35 +/- 0.2 bar (5.1 +/- 2.9

PSI) in the engine.

Operation / Operating principle:

normally closed

switch. With oil pressure above 0.35 +/-0.2 bar (5.1

+/- 2.9 PSI) open circuit.

Level in wiring diagram:

petrol reserve and oil

pressure.

Location:

•

sensor: between the two heads, at the

back.

•

connector: on the sensor.

Electrical characteristics:

•

With engine off: closed circuit (continu-

ity).

•

With engine on: open circuit (infinite re-

sistance).

Pin-out

: Voltage 12V

Instrument panel

Warning light always off

Troubleshooting

•

Check the sensor connector and the instrument panel connector (PIN 17): If not OK, restore.

If OK, check the continuity of the purple cable between the sensor connector and the in-

strument panel connector PIN 11: if not OK, restore the cable harness; if OK, replace the

sensor

Warning light always on

Troubleshooting

•

Disconnect the sensor connector and check the ground insulation of the purple cable: if there

is continuity with the ground connection, restore the cable harness; if earth insulated, replace

the switch. if the error remains, check oil pressure in the engine circuit with a pressure gauge

Electrical system

V7 Classic

ELE SYS - 56

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание V7 CLASSIC







































































































































Результаты поиска

Содержание V7 CLASSIC

Отзывы:

Похожие инструкции для V7 CLASSIC

Бренды по названию

Популярные бренды

MOTO GUZZI V7 CLASSIC, Руководство по обслуживанию

Результаты поиска

Содержание V7 CLASSIC

Отзывы:

Похожие инструкции для V7 CLASSIC

Бренды по названию

Популярные бренды