MOTO GUZZI V7 CLASSIC Скачать руководство пользователя страница 58

Страница: 58 / 134

•

sensor: under clutch lever

•

connector: under the fuel tank

Electrical characteristics:

•

Clutch pulled: closed circuit (continuity)

•

Clutch released: open circuit (infinite resistance)

Pin-out:

1. Ground connection

2. Voltage 12V

DIAGNOSIS

•

Although the clutch lever is operated, the vehicle does not start. Check that if the gear is

engaged, the stand is retracted; if it is OK, check continuity of the brown/green cable be-

tween the sensor connector (cable harness side) and the main injection relay: if still there

is no continuity, restore the cable harness; if there is continuity, disconnect the sensor con-

nector and check, with clutch pulled, if there is continuity between the 2 PIN of the connector

on the sensor side. If there is not continuity, replace sensor; if there is continuity, check

continuity of the purple cable between sensor (cable harness side) and start-up relay; oth-

erwise, restore the cable harness.

•

The vehicle starts without pulling the clutch lever: disconnect the terminals from the sensor

and check if the released clutch sensor has continuity between the 2 PINS; if there is con-

tinuity, replace the sensor; if there is not continuity, it means that the purple cable from the

sensor PIN to the start-up relay is shorted to ground.

Side stand sensor

Function

It tells the side stand position to the control unit.

Operation / Operating principle

If the gear is engaged and the side stand is unfolded, and therefore the circuit is open, the control unit

does not enable vehicle start-up or shuts off the engine if it is rotating.

Level in wiring diagram:

start-up enabling switches

Location:

•

sensor: on side stand supporting plate

•

connector: left side, near the starter motor

Electrical characteristics:

•

Side Stand Up: closed circuit (continuity)

•

Side Stand Down: open circuit (infinite resistance)

Pin-out:

Electrical system

V7 Classic

ELE SYS - 58

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание V7 CLASSIC







































































































































Результаты поиска

Содержание V7 CLASSIC

Отзывы:

Похожие инструкции для V7 CLASSIC

Бренды по названию

Популярные бренды

MOTO GUZZI V7 CLASSIC, Руководство по обслуживанию

Результаты поиска

Содержание V7 CLASSIC

Отзывы:

Похожие инструкции для V7 CLASSIC

Бренды по названию

Популярные бренды